Interroom doors - actual ideas for a modern interior. Unsurpassed quality and appearance of solid wood interior doors Prices for entrance doors

Let's look at a few of the most simple ways do the decor of interior doors with your own hands using improvised materials.

As you know, doors are not eternal, and anything can happen. For example, often scratches, chips, cracks appear on the door leaf. In this case, you can repair, replace or decorate carefully, hiding all defects.

Covering the door with wallpaper

To decorate the door, you can use not only paper, vinyl and non-woven wallpaper, but also fabric or liquid.

In this case, the canvas should be prepared by removing a layer of paint in advance, filling irregularities, cracks and sanding the surface.

The applied primer layer will provide additional adhesion of the wallpaper to the door surface.

Wallpaper can be pasted over both the entire canvas and the panels, cutting out pieces of wallpaper of a suitable size. Don't forget to choose the glue that suits the type of wallpaper and dilute it according to the instructions.

Wallpaper classic

Lubricate the cut wallpaper with glue and apply it to the door, making sure that there are no jams and distortions. We smooth the wallpaper with a soft cloth, roller or wide plastic spatula. Carefully cut off the excess with a clerical knife. Additionally, you can decorate by gluing a foam plinth frame over the wallpaper.

For the period of drying of the wallpaper, it is advisable to close the windows in the house and exclude the appearance of drafts, a sharp temperature drop.

Textile

The door decorated with fabric looks very unusual and attractive. In addition to the standard surface preparation, attention should be paid to the fabric itself, ascertaining the degree of shrinkage.

We cut off a small piece of fabric, measure its dimensions, moisten it with water and dry it. After drying, we again take measurements, comparing the readings and finding out the degree of shrinkage. If the value is large, then we also wet the entire piece of fabric before decorating and leave it to dry.

Note! You can use not only a single piece of fabric, but also cut fragments of different colors and textures. This technique is called "patchwork" and is often used by designers in the design of premises.

For fabric, casein glue, a composition based on CMC, as well as Bustilat or Gumilaks mastics are best suited. We apply the adhesive to the fabric and apply it to the door, smoothing it with a spatula. When pasting the door with fragments, it is important to monitor their geometry, otherwise the work will look sloppy.

Additionally, you can decorate the door with beautiful furniture carnations, shiny nylon or leather cords, fabric paint, baguette frames.

- are universal. They cover not only walls, but also doors, creating unimaginable patterns and compositions. In this case, you do not have to mess with cutting canvases. However, it will not be possible to expose the door to moisture. Therefore, for decorating a door in a bathroom or kitchen, this method is unacceptable.

To work, you will need a dry wallpaper mix, several spatulas of different sizes, a hopper gun, a roller, a clear varnish, a color scheme.

Decorate the door with a mirror

Highly unusual finish doors can be crafted using mirrors. Such decor will not only attract everyone's attention, but also visually expand the space of the room, add light. However, cutting and attaching a classic glass mirror is very inconvenient, since there is an alternative - acrylic panels with amalgam, which has excellent reflectivity.

Acrylic mirrors are available in a wide range of colors. You can choose any shade you like or several to make a mirror panel. Plastic panels do not break, are easily processed and attached to the door, and are light in weight. The cost of mirrored plexiglass is not the lowest, but the quality and aesthetic qualities are fully consistent with the declared prices.

Before attaching the mirror plastic to, you should carefully level the surface by deepening the nail heads, sanding and covering all the bumps / recesses with putty.

On the door and the back side of the acrylic sheet in without fail a deep penetration primer is applied. After it dries, the cut panels are fixed with double-sided tape and mounting glue. For convenience, use mounting suction cups, with their help it is much easier to carefully glue the panels to the door leaf.

As one of the decoration options, you can consider figured acrylic mirrors. Such a mirror can be attached in the center of the door or you can purchase several elements and arrange them beautifully. Usually small parts are produced with an adhesive layer already applied.

Even from this simple material, like buckwheat husks, excellent work is obtained. The cost of the material is minimal, but the service life of such a coating, unfortunately, cannot be called too long.

Step 1. Remove the layer from the door old paint, the existing vinyl coating, we eliminate all irregularities with putty.

Step 2. Remove the door from the hinges and put it on the floor / stools / table. We paint the door leaf with dark brown paint. If there are glass inserts on the door, we protect them with masking tape.

Step 3. We thickly grease the dried door with PVA glue, lay out the husk, distributing it with our hands. If necessary, add small gold sparkles.

Step 4. We cover the door with a transparent varnish (glossy or matte). It is advisable to apply three layers in order to qualitatively fix the buckwheat on the door leaf.

A beautiful door is ready. So that the door does not stand out from the overall design of the room, decorate the picture frame in the same way and place the creation on one of the walls.

We decorate the door in vintage style

Vintage is sophistication and sophistication, the beauty of artificially aged things, in harmony with the chic of individual decorative elements. The door in vintage style will become a work of art, an exclusive element of the interior.

For decoration you will need:

We will combine door painting with decoupage technique and in addition we will add decorative elements. We will carry out the work on the already removed from the hinges, puttied and carefully sanded door, laid horizontally.

Step 1. Paint the door white. We apply the paint with a wide brush with stiff bristles in one direction, in a thin layer.

Step 2. When the paint dries, gently sand it with coarse sandpaper, achieving the effect of "old times".

Step 3. We start decorating the panels or the central part of the door. We tear musical notebooks and old newspapers into small pieces with our hands. We draw a field for activity of a rectangular or square shape on the door with a pencil. Lubricate the outlined areas with PVA glue. Immediately lay out the paper randomly, smoothing it with your hands. On top, apply a transparent varnish in two layers.

Step 4. Along the perimeter of the areas pasted over with paper, we fasten a black baguette to the mounting glue.

Additionally, you can decorate with a beautiful wreath, a large lace bow or plastic beads imitating pearls (glue-based).

There are many other ways to decorate doors. Operate with the materials available in your home arsenal, connect your imagination and create your own masterpieces.

Entrance door prices

Entrance doors

Video - A variety of ideas for decorating doors

Video - Applying patina to the door

Video - Self-decorating the door

11 best manufacturers of interior doors

Doors el'PORTA

Doors el'PORTA are doors with Italian architecture, produced in Russia. Models modern design and trendy shades, materials of the highest quality. Interior doors el'PORTA are produced on modern Italian and German equipment. Various decorative door coverings allow you to choose the best option in terms of price and performance.

Characteristics:

• 3D-Graf - Structural decorative material increased density. It has a pronounced texture, medium wear resistance;
• eco-veneer is an anti-vandal decorative material that imitates a cut of a real tree. High wear resistance, resistance to mechanical damage, fading, moderate resistance to moisture;
• aqua doors - doors that are not afraid of moisture;
• enamel - a multilayer material that imitates enamel, but has higher.

Doors EL'PORTA

- each product is an effective combination of priorities modern materials, trouble-free fittings, successful structural and design solutions. Such doors are very appropriate in rooms decorated in modern high-tech or minimalist styles.

Characteristics:

• modern innovative coating Renolit (Germany) stands out for its strength, durability and environmental safety;
• carelessness. It is enough to wash it occasionally with ordinary furniture care products (not containing abrasives);
• doors can be installed in any room, even with high humidity;
• easy to use, as well as durable and reliable.

— Stylish minimalist design will appeal to the modern city dweller. A rich choice of textures and finishes allows you to harmoniously fit these doors into a new, as well as into an already finished interior. Telescopic door trim- this is constructive solution door frame to fit any wall thickness.

Characteristics:

• due to the telescopic effect, the design is suitable for walls of any thickness. Thanks to a tighter fit to the wall, the box does not warp over time;
• harmless material based on polypropylene;
• a jointed massif of Angarsk pine is used in order to ensure the stability of the frame, low weight of the canvas, as well as the environmental safety of consumers.

Sofya doors are an author's design product, impeccable European quality and prompt service. Factory "Sofya" performs a full cycle of product creation from the development of the design of each door collection with Italian designers, the development of manufacturing technologies with German engineers.

Characteristics:

• door painting based on safe components based on acrylic, which are used in the medical industry;
• absolute precision in the execution of all joints in the most unusual collections;
• careful selection and research of the materials used;
• ecological, strong and durable in operation.

— direction Design by ARTDEKO is interior doors for true connoisseurs of beauty and comfort. warm shades natural wood, refined forms, luxurious decor of classic doors will become a real decoration of the interior. Manufacturability and laconic forms of doors in a modern style are an example of high design for adherents of minimalism.

Characteristics:

• veneer is used from valuable wood species such as oak or ash;
• inserts made of transparent, frosted, colored or patterned glass;
• are made on high-tech equipment by qualified specialists using high-quality raw materials and materials.

- this type of door structure is a collapsible structure made of individual elements(king). The main advantages of this design are its high maintainability, due to the ability to replace any part of the door during operation and a huge range of various models both modern and classic style.

Characteristics:

• resistance to chemical and physical influences;
• a feature of the coating is its pronounced deep “brushed” structure with a glossy lacquer monochromatic surface or a matte lacquer monochromatic surface;
• Complete with German Simonswerk hinges and German KFV lock.

The most exquisite and expensive renovation will look unfinished if old doors remain between the rooms or new ones are chosen tastelessly and do not match the interior. A high-quality interior wooden door that meets modern requirements will add the missing touch to the design of the home and create the right impression of the house. This article will tell about the right choice, species diversity and features of internal doors made of wood.

The main advantage of wood is that it is made from natural environmentally friendly material.

Construction and furniture stores today offer the widest selection of interior doors from different materials. Quite rightly, for centuries the leading positions have been occupied by wooden structures. It was the tree that served as the basis for the construction of doors in houses, castles and palaces many centuries ago. And now this material does not lose its relevance.

Wood is different high quality and ease of processing. If desired, a wooden product can be given an aged look, it is easy to paint, paint or cover with any material. There is a centuries-old tradition in the production of wooden doors.

Italy is considered the leader in terms of quality indicators and the number of door sales, but such models are not available to everyone. An alternative to Italian doors are products made in Spain, Finland, as well as designs of Belarusian and domestic production.

Interior doors as a functional part of the room are designed to perform several functions, in particular:

• protective;
• soundproof;
• decorative.

Wooden interior doors, which are strong enough, reliable, environmentally friendly, have an attractive design, completely cope with all these tasks. appearance and create a unique atmosphere of coziness and comfort. Besides, wooden doors have a high degree of insulating properties. They retain heat, do not let noise through and are resistant to temperature extremes. Therefore, for centuries, wooden doors have been very popular in home improvement. In addition, they are perfectly combined with other materials in furnishing and decoration, in particular with clapboard, parquet and laminate.

Useful advice! Giving preference to wooden interior doors, it is recommended to select furniture from the appropriate material. Then the room will look harmonious and cozy.

Interior wooden door: advantages and disadvantages

Among the many various materials, perhaps, interroom wooden doors enjoy the greatest popularity. Natural wood is not as durable as metal, but at the same time much more attractive; not as elegant as glass, but more wear-resistant. This material is averaged over the list of positive characteristics, and therefore occupies one of the leading places among other types of raw materials.

Wood as a material has the following advantages:

1. Durability and long service life. Doors made of wood will last much longer than those made of chipboard or glass, while the durability of the product depends on the hardness and type of wood. Oak, beech, hornbeam, white acacia, yew are considered the hardest, and pine, poplar, aspen, cherry, linden are considered the softest.
2. Wear resistance and impact resistance. These qualities are endowed with all of the listed hardwoods, as well as juniper, birch and apple. At the same time, soft pine is able to withstand shock and mechanical stress.
3. Wood products do not require special care during operation, it is enough to wipe them regularly. In case of damage, a wooden door can be easily restored.
4. Solid and respectable appearance. In terms of aesthetic characteristics, wooden doors are not inferior to any material.

Along with the advantages, wood is characterized by some disadvantages, in particular, strength predetermines the severity of the material. Certain breeds are vulnerable to moisture, which excludes the possibility of their installation in the bathroom. But the main disadvantage is the high price of interior wooden doors.

Solid wood interior doors: the advantages of different types of wood

The quality of the doors and the maximum compliance with all the advantages depend on the material from which they are made. The range of wood (as well as the color range) is very wide, which largely determines the price of natural wood. Interroom wooden doors are made from both solid and glued solid wood or derived materials, which significantly affects the cost. For different conditions and specific rooms, you need to choose certain types of wood. To create doors, both deciduous and coniferous, and even exotic woods are used.

Useful advice! The quality of the product is significantly influenced by the preparation and method of processing the material.

The following types of trees are most often used for the manufacture of door structures:

1. Oak is the most expensive material. Oak doors are very durable, wear-resistant and serve for several decades. The material has a different color - from bleached to dark brown.
2. Beech is practically not inferior in quality to oak, but has a lower cost. Additional benefit - beautiful colour with a pinkish sheen and a uniform texture that will fit into any design. The main flaw is poor moisture resistance.
3. Ash is a non-capricious material, characterized by durability and affordable price. The strength is not inferior to oak, resistant to high temperatures and humidity.
4. Pine is the most practical and affordable breed, therefore it is widely used in the production of doors, but at the same time it has lower strength characteristics.
5. Exotic species include dark green ebony, chocolate rosewood, pink and light brown African birch anegri. It is for the beauty and originality of the colors that please the eye that some owners prefer these breeds and do not skimp on their purchase.

Interior wooden doors made of pine: a combination of price and quality

The most popular tree species are listed above. There are also exclusive varieties. For example, luxury lovers can afford mahogany interior doors. The breed is distinguished not only by the bewitching color of the wood, but also by a high degree of hardness, which makes it especially valuable. Not to mention other varieties such as cedar, walnut, maple, alder and cherry. These breeds are perfectly polished, tinted and have a delicate pattern.

A reasonable combination of price and quality is the main condition right choice wood. In this regard, interior wooden doors made of solid pine deserve special attention. The main difference is the low cost. Despite the softness of the material, pine products have high operational characteristics. In addition, they have other advantages:

• relatively light;
• pine is easily processed;
• pine doors are easy to restore.

It is unpainted interior wooden doors made of pine that are distinguished by a light natural tone that captivates buyers. Varnishes and paints allow you to get a different shade.

The main disadvantage of wooden unpainted solid pine doors is excessive softness. In addition, due to the broken processing technology, resin can be released from the wood. Therefore, before sending pine for production, it is important to dry it thoroughly.

Useful advice! In the installation of interior doors, you must adhere to one important rule. All rooms should have doors identical in material, texture and color. This applies not only to residential, but also utility rooms. The choice in favor of natural wood can cause significant costs.

Solid oak interior doors: reliability and durability

Doors made of precious wood, such as oak, beech or mahogany, are installed in respectable houses and apartments, which emphasizes the special status of the owners. These products are characterized by the following features: high degree strength, durability and visual appeal.

Oak doors do not lose their shape for a long time, they almost never crack. The minimum service life is 30 years. Its duration is significantly affected by care and proper operation. Unpainted oak doors have one important characteristic: during use they change their color - from light beige to dark brown. Therefore, before painting solid oak wooden interior doors, this feature should be taken into account. If a decision is made in favor of coloring, then preference should be given to special expensive varnishes and paints.

There is such a type of processing as staining by soaking wood for a long period. Products made of bog oak are highly valued, they have increased strength, flexibility and impact resistance, they are distinguished by a dark color.

The main and indisputable disadvantage of oak products is their high cost. The price of a wooden interior door with an oak frame is twice as high as a similar option made of pine or alder.

Types of interior doors according to the method of manufacture and design

In addition to solid wood, other materials are also used in the manufacture of door panels. In particular, structures can be panel and panel. The first type is presented in the form of a frame, which is sheathed with timber bars. The middle is filled with a monolith or honeycomb material, which guarantees increased sound insulation. Such doors are deaf or glazed.

Related article:

Entrance wooden door. The difference in designs and ways of functioning. Self-manufacturing and installation tips.

The manufacturing process of interior paneled wooden doors is much more complicated and labor-intensive. The main frame, called the strapping, consists of bars, mullions are installed in the middle (also made of bars). The space between the strapping and the mullions is filled with special inserts made of paneled panels, glass or a combined type.

A common manufacturing method and a more budget option are doors made of glued solid wood. The door leaf is made from cut wood bars. The glued structure differs from the solid array in less stress, therefore it is less susceptible to deformation and is more resistant to moisture. The high aesthetic and stylistic characteristics of these structures are evidenced by photos of doors made of glued solid wood.

Design features of wooden interior doors: photo examples of different types

Interroom wooden doors have a different design. It is chosen depending on the area of ​​\u200b\u200bthe room. The main differences are the method of opening and arrangement of the doorway. Thus, they can be hinged, folding and sliding.

Useful advice! The level of wood moisture is an important indicator in the door industry. In accordance with GOST, its level in the finished product should not exceed 12%. The excess of this criterion indicates non-compliance with the production technology, which can lead to an early deformation of the door leaf.

In its turn, swing structures are divided into single and double wooden interior doors. They are distinguished by the number of valves. For the installation of such structures, at least a square meter of space is needed so that the doors open freely. Installation of wooden doors for interior hinged type is a process that does not require special skills and knowledge.

If the space in the room is limited, then it is better to stop the choice on a folding or sliding design. A sliding wooden interior door, when opened, goes into a special cavity in the wall. The most common model is sliding doors.

Folding doors significantly change the interior of the room, creating a feeling of additional space, so installing them is ideal for small apartments. A subspecies of a folding canvas is an interior wooden accordion door, which assumes the silent movement of door elements in the opening. Such a design is carried out without unnecessary heaps. The disadvantage of doors of this type is poor sound insulation. Installing such products in the kitchen will not protect against the penetration of various odors outside of it.

Wooden shutter doors: a new trend in interior design

Fashion trend in interior design recent times louvered doors were installed. If initially they were used as decor items, now they are increasingly used as partitions between rooms - in the form of interior doors. The popularity of the design is due to a number of advantages:

• originality of design;
• aesthetics and versatility, providing the ability to install the structure in different interiors;

• environmental friendliness due to the manufacture of wood products, which has a positive effect on human health;
• freedom in choosing the shape, type and size of louvered doors;
• practicality, which lies in a wide scope of application both in the traditional form and in the form of an accordion door;
• the benefits carried out due to the free circulation of air, contributing to the ventilation of the room;
• affordable cost and ease of installation;
• choosing the method of manufacturing a louvered door - to order or independently.

The ability to make shutter doors with your own hands is considered one of the main advantages. However, for this you need not only to have elementary carpentry skills, but also be patient, since the process is not so much complicated as monotonous and scrupulous. If the temperament is not distinguished by perseverance, then it is better to make louvered wooden doors to order.

Useful advice! When self-painting or manufacturing louvre doors to order, one should take into account their compliance with the style of the room. For example, for classic interior doors with a golden brown finish are suitable, and for country, provence or mediterranean style, white louvered doors are the best choice.

Features of the choice and installation of interior doors in a wooden house

In a wooden house, as in any dwelling, its zoning is an important factor. Interroom doors will help to satisfy this requirement. At the same time, it should be taken into account that design features log cabins involve a number of difficulties in the process of installing interior doors in a wooden house.

To avoid difficulties, you need to competently approach the process of choosing doors. It's not worth saving here. Their quality, beauty and durability depend on how much wooden interior doors cost.

The criteria for the right choice are:

• wood of high quality varieties, better than valuable wood species;
• the use of special paints and varnishes and processing technologies;
• compliance of the box with the canvas;
• high level of sound insulation;
• quality fittings.

The optimal choice of material for interior doors in wooden house- This is an array of oak or other strong species with a good texture.

The assembly of doors involves several stages. First, the box is mounted, then hidden hinges are fixed on the canvas and holes are made for handles and latches. Next is the installation of the lock and the installation of platbands. These works are recommended to be entrusted to professionals. Given the design and non-standard features of log cabins, it is better to make wooden interior doors to order.

Restoration and repair of interior wooden doors

The advantages of wooden doors include their durability, the possibility of repair and restoration. The type and complexity of the work depends on the nature of the damage. Sometimes a simple small scratch spoils the appearance of the entire product.

Remove microdefects in the form of scuffs and small scratches You can use special markers and retouching pencils. Scuff marks can be eliminated with spirit and texture pencils, allowing you to preserve the grain of the wood without damaging the base.

Restoration of interior wooden doors also includes the removal of deep scratches and even chips. A special wax will help to solve this problem, the application of which almost completely eliminates defects. Wax mixtures are distinguished by the degree of hardness and color. Before applying to the surface, it is desirable to warm up the composition, and then rub it into the surface in thin layers.

In order to remove very deep damage, you will have to purchase a special wood putty. It is applied in several layers, while allowing each previous coating to dry completely. Irregularities are eliminated with sandpaper - already smooth surface varnished in the appropriate color.

Interior doors have not only a functional purpose as a means of zoning a home, but are also an important element of the overall interior and style design. Therefore, connoisseurs of beauty, quality, reliability and style should opt for wooden structures. Modern manufacturers offer a wide range of products from different types of wood, with a variety of shapes and designs. The main disadvantage of wooden doors is the high price due to the strength and durability of natural material.

Today the door market is unique and diverse. What are the advantages of a wooden door? How to choose? You will find answers to these and many other questions in the article.

Choice of wood

Doors are an important part of every home. They perform decorative and protective functions. Doors are made from different materials:

• plastic;
• wood;
• metal;
• glass;

But the tree maintains a leading position. It is considered a sign of good taste and wealth. Wooden doors are an environmentally friendly product.

Types of wood

Oak. An amazing tree that combines strength and attractive appearance. Oak products perfectly suppress noise, retain heat well. They have the longest service life. One of the few tree species more or less tolerant of humid environments.

Alder, in terms of characteristics, is slightly inferior to oak.

Pine. It is the most budget option. Due to its availability and price, it occupies more than 78% of the market share of wooden doors. It has a high resin content, which is a natural protection against moisture.

Suitable for cities with high humidity and rainy seasons. Resin also affects the containment of heat. If you do not have a standard opening, then you can use the service - making a door to order.

Entrance doors

Entrance wooden doors are not in great demand now. About 85% of the market is occupied by metal. But wooden doors are an indicator of taste, they are durable, attractive in appearance and are an environmentally friendly product.

Requirements

Each type of door has specific requirements.

• Must be sealed.
• Must be strong and secure.

The door intended for a private house or apartment must have at least two types of locks.

Soundproofing is important. If you are choosing a door to a private house, pay maximum attention to this item.

Also, the main task of the front door is to retain heat in an apartment or house. This is facilitated by a special heat seal. Also, special rubber bands must be stretched over the door body. They create a certain tightness, which allows you to retain heat.

Pay attention to the installation of the door. Your safety, safety of things and equipment, comfort will depend on how the door is installed.

The door must be smooth, without various deformations, distortions, tuberosity, etc.

Types of entrance doors

Solid wood door. They are made from a large wooden canvas or from several connected with glue.

Shield doors. They have a certain base (shield) which is sheathed on both sides with wood. The thickness is obtained from two to three centimeters.

Combined. These are panel-type doors sheathed with metal on the front side. This gives the design reliability and safety. It is the most versatile type.

Interior doors

Suitable for interior doors:

• Ash.
• Larch.
• Pine.

They have a long service life, high strength and wear resistance. Well suited for cold regions, they perfectly retain and retain heat in the room.

Types of interior doors

• Sliding doors.
• Sliding.
• Swinging open.

Important! Bathroom and kitchen doors must be treated with a moisture-repellent agent.

Wooden doors to the balcony

Wooden balcony door performs a number of very important functions. The main thing is to maintain a comfortable microclimate in the room. In most models, glass inserts are used, this gives the room a certain style.

According to the type of installation, wooden doors are divided into:

Combined. Doors come as a set with a window, they must be installed together. These models have glass inserts.

Doors installed separately, it does not require a window. Deaf doors, do not have glass inserts. Ideal for balconies without glazing or used as a warehouse.

• The material is safe, non-toxic and environmentally friendly.
• Wood is a natural material, has a fibrous structure that allows it to “breathe”.
• On the this moment sold a huge number of different: mixtures; aerosols; varnishes; paints; impregnation; etc., which allow to extend the service life, protect against moisture, sun and mechanical damage wooden crafts.
• Nice appearance.
• Good soundproofing.

Among the shortcomings can be identified:

• rather high price;
• the need to periodically paint the product with paint or varnish;
• if you live in a region with high humidity, then you need to monitor the material and prevent attempts to swell, rot. There are special coatings for this;
• it is possible that various insects, insects, etc. will take a fancy to the door.
• since wood is a natural material, it tends to age and lose useful properties over time;
• With prolonged exposure high temperature and dry air, the door can deteriorate and crack;
• Wooden doors ignite quickly in a fire.

Making doors at home

Wood is a material used for the manufacture of various handicrafts. It is characterized by attractive appearance, smell, environmental friendliness. Finished wooden products belong to the premium class and not everyone can afford them.

Making a wooden door with your own hands is very difficult. Required:

• High quality, well crafted material.
• Tools specially designed for woodworking.

Step-by-step instruction

Choose boards of the size you need.

Needs to be processed wooden planks. For this, a grinding tool is used. It is important to process every millimeter of the board. If you miss even one area, then when painting it will be noticeable and spoil the appearance and safety of the product.

A laminated board is also required. It acts as a decorative element.

Important points when choosing

Manufacturer. When choosing, focus on the reputation of the company. They care about their reputation, have unique developments, manufacturing technologies and quality material. Their doors will be reliable, durable, aesthetically beautiful and safe.

When buying, ask the seller for a certificate of product quality. A genuine certificate is a guarantee that the doors are made of environmentally friendly material, treated with substances that guarantee resistance to water, sun, fire. Products are safe and do not contain hazardous chemicals.

The original certificate contains:

• door name;
• manufacturing firm;
• who is the supplier;
• organization that issued the certificate.

Pay attention to outward manifestations of quality. The material must be well machined and polished. The product must be smooth, without scuffs, bumps, crevices or scratches. It must also be painted or varnished.

See if the coverage is even? Run your hand across the surface. If you feel smooth then everything is processed well. If you feel roughness, sharp needles, then it is better to refrain from buying.

If there is glass, find out its type. It must be: Resistant to impact and other physical impact, whether accidental or intentional. Film is important. It will not shatter into fragments if damaged. If you have small children or plan to have them, then check this point before buying.

Photo of wooden doors

Choosing interior doors is not as easy a task as it might seem. What material and what type of construction to choose, and how to correctly fit the door into the design of the room - read our detailed article. Compilation the best photos attached.

Interior doors, of course, are an extremely important design element of any room and apartment as a whole. After all, it is the doors that connect the two spaces that must be in harmony with both rooms, regardless of whether they are made in the same general style or inspired by completely different ideas.

So, when in the process of repair you are faced with the question of choosing interior doors, you should pay attention to a few basic rules.

1. Naturally, the ideal option would be doors made of natural materials. We will not tire of repeating that good stuff- this is not only an aesthetic choice, but also the basis of the longevity of a particular design element, and this indicator can more than recoup the costs. On the choice of interior doors the best choice– doors made of solid wood or natural veneer.
2. High-quality coverage is another point worth paying attention to. close attention. It is a high-quality coating that will help extend the life of the door without losing their attractive appearance. In addition, high-quality varnish or laminate is also a matter of health!
3. Pay attention to the fit of all door elements: there should be no extra gaps at the junctions of individual parts, such as gratings, frames, glass inserts or other materials.
4. Correct geometry is what matters! Only minor discrepancies of a few millimeters are acceptable, otherwise you risk getting certain problems with installation and operation in the future.
5. Remember that the door frame must be with a seal, and if glass is used in the decoration, then it must also be of sufficient quality to adequately endure all operational moments!

​

Deciding on the material

fiberboard

Doors made from fiberboard, or in other words fiberboard, are a relatively cheap option. Unlike chipboard, which contains formaldehyde resins that emit toxic fumes over time, fiberboard is a more environmentally friendly material. It is a slab made from pressed wood dust, the wood particles in which are steamed during the production of the slab, and therefore they speak of production by wet pressing.

Do not think that fiberboard doors look like the back walls of Soviet wall cabinets. In the production of doors, fiberboard is ennobled by pressing with special dyes. In addition, the material undergoes the so-called strengthening process, which also positively affects its external and functional qualities.

All in all, MDF doors are a good economical choice, with a number of other benefits: MDF doors are moisture resistant and durable enough to last you a long time.

MDF

MDF is an excellent compromise between the price of the product and its quality. Not only is MDF an environmentally friendly material, but everything else it has an excellent texture that allows you to make any carved elements from it. Therefore, if you want a door with an interesting decor, MDF will do the job perfectly.

MDF can be an excellent "stuffing" for an interior door. External finishing in this case can be done, for example, from natural veneer. If you are considering more budget options, then you can opt for faux veneer or lamination.

In addition to the advantages associated with possible design refinements in the performance of the door leaf, MDF has other advantages, including:

• moisture resistance;
• durability;
• practicality;
• deformation resistance.

solid wood

If you want the doors in your apartment to look expensive and noble, serve you for a long time, and at the same time you are ready to pay the appropriate price for it, your choice is solid wood interior doors.

A wonderful natural material, wood, has a number of advantages:

• strength of the door structure;
• excellent adhesion to finishing materials;
• reliability of fasteners;
• environmental friendliness;
• high quality;
• a wealth of design options.

But this material, unfortunately, is not without its shortcomings:

• each door made of solid wood is universal in a certain sense, since the pattern of the tree is unique;
• low resistance to temperature extremes and moisture (high-quality coating and proper care are required);
• a large weight of the structure, involving the use of extremely reliable and strong fittings.

Most often, in mass production, the surface of solid wood doors is covered with thin sheets of natural veneer - to improve moisture and heat resistance and increase the service life. With this task, veneered wooden doors cope perfectly!

Glass

Many modern styles, such as hi-tech or minimalism, do not like such natural materials as a tree or an artificial imitation of wood canvases. The futurism of such styles dictates the choice of completely different materials - metal, plastic, glass.

And if metal doors are not the best choice for dividing rooms, then glass doors, on the contrary, do not look pretentious and somewhat simplify and facilitate. The matte surface makes it easy to fit them into any room and use them, including as a door for and.

In addition, the possibilities of decorating glass sheets are multifaceted! The combination of frosted glass with ordinary glass, stained-glass windows, sandblasted drawings - all this will help you choose a truly unique door for a unique interior!

Choosing the design of the interior door

Exists a large number of options for interior doors, including classic swing doors, and more interesting designs - sliding or folding. About all the details - below.

swing doors

Swing doors are the simplest and most familiar type of doors. The design of such a door consists of a door leaf and a box. But even such the simplest doors currently boast some variety of options.

A similar design and type of opening is currently used everywhere: both as interior doors and as entrance doors.

Sliding doors

Such a currently popular type of door construction as sliding doors came to us from Asia, where they have been used since ancient times. Their main advantage is ergonomics.

The design is a door leaf, which is attached to a guide with rollers installed inside a beam attached to the wall. The rollers are attached to the top of the door with a special bracket.

Sliding doors are able to fit into the smallest room, allowing you not to save precious meters.

Let's highlight the main advantages of the sliding type of opening:

• space saving, which allows not to waste space in an irrational way;
• design safety;
• stylish and fashion design.

The main disadvantages include low sound and heat insulation, as well as a higher cost compared to classic sliding doors.

One way or another, sliding doors are a stylish and modern version of interior doors. We invite you to familiarize yourself with interesting examples in our photo gallery:

Sliding doors

Compartment doors belong to a subgroup of sliding doors, however, they differ somewhat in design from the classical type, and therefore we singled them out as an independent group.

The design of such doors is similar to classic doors. But of course, interior sliding doors differ from cabinet doors in weight and strength. In addition, do not forget about the presence of a handle and a lock.

Compartment doors are more ergonomic than classic sliding doors due to the fact that when opened, the sliding doors not only move to the side, but also overlap each other.

sliding doors

Another interesting type of sliding doors are doors with a sliding mechanism. Such designs are perhaps the most ergonomic option possible, because the door being opened does not slide along the wall, but inside it!

The wall in this case is made of drywall, and requires partial redevelopment for mounting a U-shaped groove into the wall. The groove is best made of metal.

When installing a sliding door, do not forget about the correct position of the handle!

Such a door looks very interesting in the interior of any room and has useful property tightness compared to a conventional sliding door.

Roto doors

Roto doors are a kind of compromise between a swing and a sliding door. The peculiarity of the roto-door is that in the process of opening the door leaf turns a little and in the open position it becomes perpendicular to the doorway.

This type of opening allows open door take up less space and, like the design of a sliding door, it serves to save space in a small room or.

Roto doors have the advantages of soundproofing and tightness, and are the perfect solution for the bedroom!

Folding doors (accordion doors)

interesting design solution we are presented with the design of folding doors.

An accordion door can perfectly fit into the interior of a living room or bedroom, as well as become an excellent option in terms of space zoning (for example, separating the bedroom from the dressing room).

Wood or plastic is often used as a material in the manufacture of an accordion door, but other options are possible.

The design of a folding door is a connection of several elements using movable hinges, and one of the ends of such a door is equipped with rollers moving along a guide, as is the case with a classic sliding door.

Nuances of choice and design tricks

A single style or a riot of diversity?

When choosing interior doors to an apartment, we are faced not only with the choice of material and type of opening, but also with the choice of style, which, as often happens, should “combine the incongruous”. What are we talking about? Let's tell you more.

If you are doing repairs in private room and along with the interior design you want to change the door, you are faced with the task: how to choose a door that would simultaneously fit into the new interior of the bedroom or living room and fit into the corridor? However, such a question haunts those who create a design project for a future apartment.

After all, it often happens that completely different styles coexist on the same living space in different rooms! A bedroom in the style of gentle Provence, a living room in the Art Nouveau style with its natural motifs, a laconic kitchen in the style of mimalism and a retro entrance hall - and each room has its own requirements not only for furniture and interior design, but also for the door!

Of course, if you plan to choose a single style for decorating an apartment, then you won’t have to puzzle over how to fit the door into two interiors at the same time. If you decide not to go the easy way, then we can advise you to make interior doors to order - so you can arrange them on the one hand to match the design of the hallway, and on the inside - choose a finish that is more suitable for the chosen style of the room.

You can also choose doors in neutral colors and neutral design, which will allow you to fit them into any interior of your choice without any questions!

Tall interior doors

We are used to standard doorways that average 30-50 cm below the ceiling (depending on the height of your ceilings). However, designers are increasingly offering us interesting concepts with the use of high doors in the interior - literally from the floor to the ceiling! What are the advantages of such structures, in addition to an unusual design solution?

• High doors can visually enlarge the space of a small room and “raise” the ceilings.
• The richness of the choice of style solutions and shades can easily emphasize the individuality of your design.
• The originality of the appearance does not even need comments. Such doors are unusual, period.

Self-installation of interior doors

Installing interior doors with your own hands is not the easiest process, which, however, allows you to save a lot during the repair process.

Of course, the nuances of assembly and installation directly depend on the type of construction you have chosen and it is impossible to identify a universal algorithm suitable for any case.

We tried to compile for you video tutorials on installing interior doors various types, to this process gave you as little trouble as possible! So, let's watch the video:

Swing door installation:

Sliding door installation:

Folding door installation:

Installation of rotary doors:

Obviously, for a modern owner of an apartment or a private house, an interior door is not only an interior element that allows you to create a certain isolation of one room from another, it is also a decorative component of the image of the entire dwelling. And the question of choosing this important and functional piece of furniture ceases to be simple when the consumer is faced with a huge range of modern stores, where doors are presented in a wide price range, design variations, made of various materials with all kinds of color solutions. Well, the possibility of manufacturing custom-made doors completely erases the boundaries of choosing this piece of furniture. So, which door to choose by color? What design to give preference, so as not to violate the overall design style? How to find a practical and at the same time inexpensive option? Let's sort it out in order.

The choice of shape, size and type of design of interior doors

To begin with, the choice of doors for your home should be addressed at the initial stage of renovation planning. Even if all the doorways of your premises have standard sizes, you need to make sure of this in advance so that you don’t have to look for a door leaf standard sizes or order individual production (which will entail not only additional costs, but also stretch the repair over time).

Speaking of width doorways for single-leaf doors, their sizes are usually presented in standard 60, 70, 80 and 90 centimeters. But the height of the door panels has recently fluctuated with various manufacturers. Not so long ago, it was difficult to find doors with a height of more than 2 m, but now there are a lot of such options - 2 m and 10 cm, 2 m and 20 cm. Designers recommend using interior doors of non-standard height for visual "raising" ceilings. If your needs are not within the standard sizes, then you need to prepare the doorway in advance for the canvas you like, or look for doors for existing designs.

Of course, in the modern market of interior doors there are enough companies that will manufacture the product according to your size and individual design. Such a canvas will not only fit perfectly into the existing picture of the interior, but can also become its highlight, thanks to its exclusive execution. But you will have to pay for an individual approach. Nevertheless, most buyers prefer to purchase interior doors from the assortment of the store.

From the point of view of dividing doors by type of construction, the most popular for our compatriots are single-leaf and double-leaf swing doors. The usual design and mode of operation take up the trendy offers - turning or semi-turning door leafs.

Agree that swing door in the open state, it takes up a lot of useful space in the room, and a certain amount of space is required for the opening itself. In small spaces, designers suggest using variations of sliding doors. The first way to create such a design is to place the door leaf between two rails that are attached to the ceiling and floor. As a result, we get sliding canvas operating on the principle of compartment doors. Recently, this method of creating room isolation has been simplified to a single hanging rail or tripod that is attached to the walls above the doorway. Thus, it is possible to save space in small rooms, but it is important to understand that furniture or other interior items cannot be installed close to the wall at the place where the door leaf moves.

Sliding doors are no less popular in recent years. The main task of such a design, in addition to its main function of isolating rooms, is to save space. The door slides into a specially designed drywall box or directly into the walls. As a result, the canvas does not interfere with anyone and does not take up space in a small room.

Two and three-leaf doors, which fold like an accordion, can become the best option for rooms in which there is no possibility of installing sliding structures, but there is a need to save space.

Another design of interior doors, which cannot be ignored, is the shelving door. Differing not so much in the type of opening, but in their very appearance, such doors can be found at the entrance to the living room, which also performs the functions of a library or an office. A door with open shelves is most often used to store books and therefore has a rather large weight, which complicates not only the entire structure, but also requires certain properties from fittings.

Execution material - choice with financial reference

The choice of material for the execution of interior doors directly depends on your financial capabilities. Of course, the style of interior design, the specifics of their functionality (kitchen, bathroom or toilet) are also the criteria for choosing the material for the manufacture of doors, but do not play a decisive role.

Currently, the following types of materials for the manufacture of interior door panels can be distinguished:

• fiberboard doors - the most popular option, affordable and with a wide range of choices. The advantage of such doors is their low weight and ease of use. But if we talk about the durability of use, then such models are in last place;
• MDF canvases are more expensive than fiberboard products, but this is due to their high strength and reliability. Such interior doors can be used in rooms with humidity above average. Cloths create excellent sound insulation;
• solid wood products are an unfading classic of any interior items. Such doors are not cheap, but they can serve for decades (doors made of wood can be inherited by your younger generation with proper operation). Often, manufacturers use wood of light and inexpensive species (for example, pine) as the basis for doors, and sheathe it with veneer from more noble species. Thus, it is possible to reduce both the cost and the weight of the product.

All these options for doors made of various materials can be presented both in a deaf form (panel) and with glass inserts. Speaking of glass as a material for the execution of door panels. In modern design projects, more and more often you can find doors made exclusively of glass, without frames and profiles. Such designs look light and fresh, bring to the interior not only the motives of industrialism, manufacturability, but also the possibility of visual expansion of space. Doors made of tempered, human-safe glass (even if such a canvas breaks, which is not easy to achieve, a person will not be able to get hurt by fragments due to a very strong protective film) practically do not prevent the penetration of light, which allows you to maintain the illusion of spaciousness even when the rooms are isolated.

Color palette - decide on shades

Choosing the color of door panels is not an easy dilemma. On the one hand, there are no strict rules in this regard, on the other hand, I would like to see a harmonious combination of all interior elements in my own home. We install doors not for a year, but often for decades, which is why it is important to approach the choice of this piece of furniture with all responsibility. The first thing to decide is whether you want the door panels to merge with the general colors rooms or become an accent in your interior?

You can follow the path of elimination. Depending on the area of ​​​​your premises and the degree of illumination, you can exclude dark options execution of door panels that will visually emphasize the modest scale of the dwelling. Experts recommend light doors not only for small and poorly lit rooms, but also as a versatile design that can be easily combined with a simple and concise finish, minimalist design and does not attract attention, leaving the opportunity for other interior items to take the lead.

But designers will be able to tell you about a dozen reasons for using dark door panels in the interior. And one of the first will be a feature of stylistic design. For many stylists, it is necessary to create contrasting, accent elements that not only attract attention, but also bring clarity to the interior, give rigor and constructiveness.

Many people prefer to choose door leaves to match the color of the flooring. This method of creating a harmonious image of the room works if the flooring in all rooms of the apartment or house is the same, at least in color (in the kitchen and hallway, it can be tiles, in other rooms, laminate, parquet or linoleum).

Another way to create a combinatorics that is pleasing to the eye is to combine the color of the door panels with the main furniture - large wardrobes or entire suites. This method is not always good decision at least in the long run. After all, you can replace the facades of cabinets or other furniture ensembles much earlier than you decide to change interior doors.

The design technique, in which the doors in the room look exactly the same as the facades of the cabinets or the dressing area, allows you to achieve a harmonious image of the room. The doors of the room and the closet may differ in size, but the stylistic design and color choice must match.

If a light walls and no less neutral door leafs are not your style, if you need a bright, colorful accent in the interior, then the door to the room is quite capable of coping with this task. A bright door can be the only accent element or maintain the tone of a key piece of furniture, but in this case it is necessary to hit the tone exactly.

Residential door design - a kaleidoscope of ideas

There are a lot of options for the execution of door panels - much more than it might seem at first glance. By and large, there are no clear rules and taboos when choosing a door design, except for one. If all interior doors face the same common room- a hall or hallway, a common corridor, then the execution of all door panels should be in the general concept. They can be made from different materials (for example, a bathroom door should be highly resistant to moisture), but at the same time look the same style. The same applies to sizes - doorways can be different widths(usually the door to the bathroom and kitchen is narrower than the openings leading to other rooms), but they must have the same height so as not to disturb the harmony of the common room.

There are many universal options for the execution of doorways that can organically fit into any style of interior design (except for very unusual, avant-garde ones). Light doors without decor can look harmonious in almost any interior, a variety of color palettes. But dark doors make any design stricter, more constructive. Dark doors will give respectability, but they will also “indicate” the size of the room - if your rooms are modest in size and the ceilings are low, then there is no point in emphasizing this fact. The natural pattern of wood with reddish hues harmoniously fits into many options for the stylistic design of rooms. It is easy to combine it with furniture from the same color group, differing in shades and diluted with light surfaces.

Any decorative inserts help not only diversify the design of the door leaf, but also stylistically connect it with other interior elements. Inserts made of transparent or frosted glass visually make the design lighter and more interesting. In doing so, you get a certain amount of light coming through the glass decor. If you want to preserve the privacy of the room, then choose frosted or corrugated glass, it is also possible to use glass decor with photo printing (if the print does not contradict the overall style of the interior).

It happens that the door leaf itself is an art object, a work of applied art. In this case, the rest of the interior is built around this element of the interior, subordinating the decoration, furniture and decor. As a rule, such doors are made to order, most often made by hand.

Interior doors - current ideas for modern interior