How to close the radiator: ways to hide the radiator with your own hands (105 photo ideas). A few simple solutions to close the battery Is it worth sewing up the batteries with drywall

Everyone who came across a repair wondered what to do with a heating battery. In many ways, these places of the premises look a little unaesthetic, due to the presence of cast iron. Which are painted with several layers of paint, and that, in turn, begins to crack and spoils the look even more. You can, of course, peel off all the layers of paint and, and even in a different color, let's say under gold, and say that it was so conceived. But then what about the wallpaper that needs to be glued on the back of the battery, and which eventually move away, and all this does not look very worthy.

Actually there is a way out! It is necessary to do that will cover the entire problem area from the floor to the windowsill from the eyes. This solution to the problem has a huge advantage. As a result, it will be very beautiful, including due to the presence of an overhead grille, which I recommend to match with the color of the furniture.

For installation you will need the following tools:

perforator with 6 mm drill
screwdriver
metal scissors
straight level
tape measure and pencil
utility knife with interchangeable blades
stapler

You will also need the following materials:

drywall 12 mm
profile 60x27
profile 27x28
sickle
perforated corner
self-tapping screws for drywall and metal
dowel-nails 6x40

Box installation

There is one condition for mounting the box: it is necessary that the window sill protrude at least 3 cm beyond the battery. In my example, the window sill turned out to be small, and I had to. It was not difficult to do this, he kept on the mounting foam. Cut out a new window sill the right size and paste it under window frame. Under it, you need to put chopsticks according to the level that you put on top of the windowsill. Next, fill the empty space between the window sill and the base with mounting foam. From above, press the load as in the photo below. After three hours, remove the load and proceed with the installation of the box.

The next step is the installation of the frame from the profile. Profile 27x28 must be installed on all adjoining: walls, floor, window sill. Pressing the profile to the base with one hand, make a hole at the same time in it and in the wall with a perforator. Install a 6x40 dowel in the resulting hole and tighten with a screwdriver. A profile 27x28 is also screwed to the bottom of the window sill, only on metal screws, the length of which should not exceed the thickness of the window sill. After that, install jumpers from the 60x27 profile.

Around the battery, decide on the size of the future decorative lattice. This place needs to be done a little smaller size gratings. There are three main standard sizes gratings: 60x60, 60x90, 60x120. These dimensions are optimal for apartment renovation, and I recommend focusing on them.

The frame is ready and proceed to the installation of drywall. Drywall is cut with a clerical knife with replaceable blades. You can find out more about how to cut drywall. Drywall is screwed with a screwdriver and nothing else. You can put a cross bit on a drill, but this is not very convenient. Therefore, I strongly recommend buying a screwdriver, but not cheap " bullshit“, but Makita or Bosch. Such a tool will serve you for the rest of your life, it is not for nothing that window companies use these brands exclusively. And so that the price of this tool will pleasantly please you, return part of the money spent,. The cost will drop by 2 times!!!

After the entire frame of the box is sewn up with drywall, proceed with the installation. They are fixed in the corners with a stapler, or you can immediately glue them onto gypsum plaster. Put a sickle on all the seams of the drywall box and cover it with gypsum plaster as well. Before wallpapering, the box must be puttied, sanded and smeared with a deep penetration primer.

Good luck with the repair!

Being engaged in the improvement of their own housing, any owner wants to create the most cozy and comfortable design in it. There are a lot of opportunities and nuances that make it possible to realize this task - but there are also a number of difficulties that arise in the process of creating an interior and impede its arrangement.

One such difficulty is associated with the use of cast iron heating batteries, whose external data always violate the measured and concise interior of the room. To solve this problem, various options for screens and boxes are used to mask unsightly looking heaters. How to close the batteries in the room with your own hands will be discussed in this article.

Battery masking methods

To hide heaters, you can use one of the following methods:

Acquisition of radiators with individual design. This method, by and large, is a preventive solution to the problem - radiators, the style of which matches the style of the room, simply do not need to be hidden. The disadvantage of this method is the very high cost of unique radiators, and not every owner can afford these devices.
Installation of a hinged screen that completely hides the working surface of the radiator.
Arrangement of a wooden element that will be installed on top of the radiator.
Creation of a drywall box that provides a complete disguise of the battery.

The latter method is the most popular among users, due to the ease of installation and the low cost of the materials used. However, a drywall box for a radiator cannot be called the most the best option, since it completely covers the radiators, and if it is necessary to repair them, the box will have to be disassembled.

Before you close the radiators with drywall, you need to carefully examine all the elements heating system that will be closed. All pipe and battery connections must be reliable and of high quality. If there are old batteries and pipes in the heating system, it is recommended to replace them before the box is installed.

A plasterboard box for masking radiators must meet two important requirements:

The heat generated by the battery must flow freely into the room, i.e. the box should not hold heated air masses;
All cranes and other communication elements must be freely accessible at all times.

Tools and materials

Before you make a drywall box for a battery, you need to prepare the following set of tools:

Drill with impact function;
Building level;
Plumb;
building corner;
spatulas;
roller;
Screwdriver;
Roulette;
Scissors for metal;
Stationery knife;
Mixing attachment for drill.

You will also need certain materials:

profiles;
Plasterboard sheets;
putty;
perforated corner;
Hangers and fasteners.

Before you seal the battery with drywall, you need to purchase such an amount of materials that will be enough to complete the entire scope of work. To guess the materials, it is advisable to have a box diagram on hand and understand how many such boxes will be needed for all radiators in the home.

Drywall box installation technology

The sequence of work required to equip a masking structure for radiators includes several stages:

Foundation preparation;
Structural design;
Frame assembly;
Frame installation;
Finishing.

Each stage of work has its own characteristics - for example, in the process of preparing the base, you need to carefully remove the old coating and eliminate any contamination. If there are certain differences on the base wall, then it must be leveled to perfect condition using gypsum plaster. Also, before you completely hide the radiators with drywall, you should putty the wall, because after installing the box there will be no opportunity to do this work.

Box design

The design of a masking structure always begins with the choice of its device. So, there are two main types of structures - a plasterboard box and a plasterboard decorative wall, behind which a radiator will be hidden. Each design has its own characteristics and applications.

The arrangement of a drywall box makes sense if the radiators are installed on the walls. You can mount such a box very quickly, and it has many other advantages - for example, the free space of a room from such structures almost does not decrease. A drywall box for a battery allows you to close only the battery itself.

The dimensions of the box must be selected depending on the size of the battery itself, which will be masked. When choosing, you need to take into account that the edges of the structure should be located at a distance of about 15 cm from each side of the battery. The box can be installed on the floor or attached to the wall, which also needs to be taken into account in advance.

The floating box, fixed on the wall, is set as follows:

A certain distance is measured from the bottom edge of the battery, at which a straight line is drawn, indicating the bottom edge of the box;
With the help of a building corner, the sides are also drawn (a distance of 15 cm between the battery and the box must be observed);
All perpendicular and parallel lines are connected, after which they must be checked with a level.

The box installed on the floor must be marked from the top side and all other lines must be taken down. When designing and marking, it must be taken into account that each side of the structure must be at least 15 cm away from the radiator. Floor boxes are ideal for hiding radiators that are deepened in wall niches.

With a strong desire, at the design stage, you can also consider more complete options for changing the design of housing. For example, a rather interesting and popular option is a solution in which not only radiators are masked, but also other elements of the heating system. To implement such a scheme, false walls made of drywall are used. Of course, the cost of work in this case increases significantly, but if the goal is to create a verified style, then these costs will be justified.

Frame assembly

The next step, which will allow you to close the battery with drywall, is the installation of a drywall box frame. Used to assemble the frame metal profiles with circus cover.

The drywall frame for the battery is assembled using the following technology:

First, the profiles are brought to the lines marked on the walls. The profiles are attached to the walls with nails and a puncher in increments of 20 cm. The fixed elements must be checked for alignment.
Next, the second level of the frame is attached. The profiles are cut to the required length and cut at the edges by 5 cm along the fold. The ends of the profiles are cut off, and the notched ones are bent to a 90-degree angle so that they can be attached to the wall profiles.
The last stage is the installation of the vertical parts of the frame on its front side.

If all the work was done correctly, then you will get a strong and fairly rigid frame with which you can work further - i.e. engage in its sheathing and the formation of a masking box.

Installing drywall to close batteries

The next installation step is cutting drywall sheets into pieces of a suitable size. To sheathe the battery with drywall, you need to attach the cut elements to the frame with self-tapping screws in increments of 15 cm. You need to tighten the screws very carefully - drywall damage may occur at high speed with a screwdriver. In addition, the caps of the fasteners can simply fall into the material and thereby render it unusable.

However, if you work carefully, then there will be no problems - it is very easy to interact with drywall. In the equipped box, the outer part will remain empty, inside which the battery will be visible. The formed window is closed with a decorative screen, which ensures the full transfer of heat into the room.

Box finishing

First you need to carry out a rough finish, which includes the following operations:

All gaps between different parts of the material and the caps of the fasteners are puttied;
When the putty has dried on the gaps, you need to putty the entire structure twice;
After the putty has completely hardened, the box is sanded.

The rough finish is complete on this, and you can proceed to the fine finish. For cladding, any materials can be used that do not violate the functionality of the structure and suit the specific chosen visual style.

Conclusion

The question of how to hide radiators can have several correct answers. To disguise heating devices, several types of structures are used, each of which has its own characteristics, both functional and visual. Choice of the most suitable option directly related to the planned design of the premises.

Not all interior styles will suit the design of a modern bimetallic or aluminum battery. The decorative properties of cast-iron radiators of the MS-140 series are even worse. To eliminate this discrepancy, decorative screens and boxes are used. And a drywall battery box is one of the popular options for solving this problem.

Is it possible to make a battery box out of drywall

The screen in the immediate vicinity of the radiator reduces heat removal from its surface, and this worsens the efficiency of the heater. But not in the case of a drywall box for heating radiators. It is enough to give an example of the design of electric convectors, in which the heating element is in a closed case with two rows of holes - from below for cold air entry, from above - for warm air to exit. Such a device increases the speed of convection, due to the fact that the duct plays the role of an air duct.

The only drawback of the method is that the battery works for heating both as a convector and as a radiator, and the screen will absorb part of the infrared radiation. To compensate for these losses, holes are cut out in the front wall of the box for the drywall battery or a factory decorative screen-lattice is installed as a front finish, and the wall behind the radiator is finished with a material with a reflective surface (for example, foil foam).

Jpg" alt="(!LANG: drywall battery box" width="500" height="450" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/08/post-16885-1221152649_copy_4..jpg 300w" sizes="(max-width: 500px) 100vw, 500px">!}

Materials and tools

For sheathing radiators with drywall, the following materials and tools are needed:

Standard sheet of moisture resistant GKL
Galvanized metal rails and rack profiles
perforated corner
Serpyanka mesh
Dowels or anchors
Primer and putty
Perforator and drill
Construction knife and scissors for metal
Screwdriver or screwdrivers
Level, ruler, corner, pencil
Sandpaper
Brushes and spatulas

Selecting a box sketch

Before sewing up the battery with drywall, you must select the type of construction. There are three upholstery options.

Hinged screen, which is hung on hook brackets attached to the wall. The advantage is the ability to remove it at any time and gain access to the battery. Disadvantage - the design of the box frame must be rigid and self-supporting, and given the weight and fragility of the drywall sheet, this is difficult to implement in practice.

Data-lazy-type="image" data-src="https://remontcap.ru/wp-content/uploads/2017/08/001..jpg 625w, https://remontcap.ru/wp-content/ https://remontcap.ru/wp-content/uploads/2017/08/001-70x53.jpg 70w" sizes="(max-width: 625px) 100vw , 625px">

Installed screen. The method consists in finishing the radiator niche with drywall. The easiest option to implement if the battery does not go beyond the niche and the screen is part of the wall sheathing. During the overhaul this technique allows you to solve the problem in a complex "how to close the radiators and pipes with drywall"

Data-lazy-type="image" data-src="https://remontcap.ru/wp-content/uploads/2017/08/004..jpg 625w, https://remontcap.ru/wp-content/ https://remontcap.ru/wp-content/uploads/2017/08/004-70x53.jpg 70w" sizes="(max-width: 625px) 100vw , 625px">

Floor box. The design is a cabinet rigidly fixed to the wall and floor, sheathed with plasterboard, the upper plane of which can serve as a window sill. This option is most popular when it is necessary to close the battery without carrying out complex repair work. But if in the second method, in order to sew up a niche for a plasterboard heating radiator, you only need to make (or buy) a front panel, then in this case it is necessary to develop a design sketch and detail with dimensions

Data-lazy-type="image" data-src="https://remontcap.ru/wp-content/uploads/2017/08/Ekran-korob..jpg 500w, https://remontcap.ru/wp- content/uploads/2017/08/Ekran-korob-300x225..jpg 174w, https://remontcap.ru/wp-content/uploads/2017/08/Ekran-korob-70x53.jpg 70w" sizes="(max -width: 500px) 100vw, 500px">

The main requirements for the dimensions of the box:

Height - the top panel must be at least 50 mm higher than the radiator surface (the standard for the location of the battery relative to the window sill)
Length - along the front, the radiator should not occupy more than 75% of this linear size of the box (the standard for the position of the battery in the niche under the window)
Depth - the front panel of the box should be 10 cm away from the battery.

How to sheathe the battery under the window with drywall - with an overhanging window sill or with a drywall top panel and slots for warm air, depends on the characteristics of the window and glass.
Usually, the window sill is installed so that it does not overlap the battery and hangs over it by no more than 2/3 of its width. It is more aesthetically pleasing if the box fits completely in width under the window sill, and in this case it will have to be changed. And it is possible that such a solution will lead to the appearance of frost and ice on the window - warm air from the radiator will not blow the glass, and it will freeze. This will not happen if there are triple-glazed windows or energy-efficient glass installed in them.
Do I need to somehow sheathe the walls behind the battery with drywall if it is covered with a box? There is no such need if the rest of the wall was not leveled and the GKL was not sewn up.

markup

AT normative documents there are no strict requirements for placing the battery under the window - it is important that its edge does not go beyond the opening from the side of the riser pipe. But when installing it, they try to make it so that it is located symmetrically relative to the window. So the installation of drywall boxes under the battery must be symmetrical with respect to the vertical axis of the window. Therefore, first you need to find and mark on the wall and on the floor the center of the window opening, from which marking should be carried out.

If the battery is not installed under the window, then its center will be the axis of symmetry of the box.
The markup sequence is as follows:

They beat off on the floor in the center of the opening or battery a line perpendicular to the wall;
From this line, measure the depth of the frame without taking into account the skin;
From the obtained point, draw a line parallel to the wall;
On this line from the center, half the length of the box is laid in each direction, excluding sheathing and trim;
From the points obtained, two perpendicular lines are drawn to the wall, and from them, using a level, two lines are drawn on the wall to the window sill.

As a result, the projection of the installation site of the box should learn on the floor and wall behind the radiator.

Frame installation

Mounting the frame begins with the installation of UD 27 × 28 profiles according to inside all marking lines on the floor and wall. Mounting step - 15-20 cm with a uniform distribution of points along all lines. The choice of the type of fastener depends on the base materials: wood screws, dowels for concrete or butterfly anchors for hollow building blocks.

A special tape is laid between the profiles and the wall, which serves as protection against the spread of structural noise.

The rest of the frame is mounted from the rack profile CW 60 × 27:

Install two corner front racks along the height of the box;
Connect them with short horizontal jumpers with vertical guide profiles on the wall;
Both racks are connected at the top with a horizontal long jumper;
To ensure the rigidity of the structure, side jumpers are added in the middle of the structure.
The number and direction of additional stiffening ribs in the front part of the box are chosen according to its size and type of screen.

After that, you can sheathe the frame.

Jpg" alt="(!LANG: drywall battery box" width="500" height="334" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/08/dccb3ffea0812d9100fc743b05b6931b..jpg 300w" sizes="(max-width: 500px) 100vw, 500px">!}

Frame sheathing

First, sheathe a niche for a drywall battery:

The side walls are cut to size and sewn up, cutting out holes for the radiator pipes if necessary;
If the window sill is not part of the box, then cut out the top panel, which closes the frame from above;
Panels are cut out of the GKL for sheathing part of the facade around the screen and these areas are sewn up.

Data-lazy-type="image" data-src="https://remontcap.ru/wp-content/uploads/2017/08/8086422_copy_1.jpg" alt="(!LANG:drywall battery box" width="500" height="450" srcset="" data-srcset="https://remontcap.ru/wp-content/uploads/2017/08/8086422_copy_1..jpg 300w" sizes="(max-width: 500px) 100vw, 500px">!}

After that, the corners are closed with a perforated corner, the joints are reinforced with sickle tape, primed, puttied and the surface is cleaned. The result should be a niche with a battery, which after finishing covered with a decorative lattice screen. Thus, the task “how to sew up heating radiators with drywall” can be solved independently.

Heating is the most important part of every winter. Thanks to him, we live the cold season in warmth and comfort, which makes the presence of a battery in the room an advantage, but the bulkiness and inelegant design interfere with planning repairs.

Large and protruding pipes are hard to imagine in a sophisticated classical style, modern high-tech direction, however, as in any other.

The usual location of the battery is the wall under the window. Due to its design, the battery stands out strongly in front of the wall. A protruding piece of metal does not add beauty to the room, which led the designers to think about how to beautifully arrange the battery in the interior.

Especially considering that the problem of protruding heating threatens the health of children. Batteries in the children's room are essential. They maintain the desired temperature, which prevents hypothermia and colds in the child's body.

But what about children's activity and sluggishness? Toddlers easily hit, burn themselves and cling to the protruding parts of the heater.

Modern apartments are put on sale with newer models, they are more reliable and safer, but they appearance far from ideal. And I don’t feel like talking about old houses with huge “monsters” as heating. The most difficult part is not to hide the heater, but to do it and not lose the main heating properties.

Popular ways to hide the battery

Every problem has its own solution. And to the question of how to close the radiators, the answer has long been found. Interior designers have found many solutions to this problem. The most used include:

Screen

The most popular solution for masking old radiators is a screen. Most often made from metal. Knowing such parameters as the width, height and length of the heater, you can easily choose the right model. Screens are stamped in in large numbers and for different settings.

The advantages of this solution include the preservation of the main function - space heating. And also the material has high strength and wear resistance, does not change shape when high temperature is cheaper than other options.

Of the shortcomings, not the best appearance. It looks, of course, much better than a battery without it, but still not suitable for every interior. More details can be seen in the photo. hidden batteries. If you have limited finances, then you can decorate the screen yourself.

wood screen

More costly and beautiful option This is a screen made of wood. Find ready-made version suitable for the parameters is difficult, so such things are made by professionals to order and are made by hand. The wood species, matched to the color of the furniture and the appropriate texture, will serve as an amazing example of how to hide the battery.

The pattern is chosen in the form of a sieve or weaving. They perfectly mask the shortcomings of the heating system and have a high heat transfer. The cost far exceeds the price of metal screens. But in return, you get a perfectly matching design detail.

Depending on the desired result, the screen can be created in the form of a high bench, cabinet, chest, or simply with additional shelves. The advantage is the ability to manufacture at home.

plastic screen

A screen made of plastic is a cheaper option than wood. But when buying, be sure to ask for quality certificates. And do not buy such an important part of the interior in non-specialized places and unknown brands.

Plastic is not the most reliable material and a product bought simply on the basis of the price can release toxic fumes at high temperatures or even melt on the battery.

A more elite option is special built-in furniture, which is made to order according to individual measurements and sketches. It is easiest to hide pipes in a table, cabinet, chest of drawers, seat, etc. But an important condition is the free circulation of air from the place of heating, which will allow both to close the battery and to heat the room without interference.

If you are an ardent opponent of noticeable pipes or extra elements in the room, then you can wall up the heating system under the walls. There are several options for execution and both are not the easiest.

The first option is to make adjustments at the stage of building a house, which will allow you to install the system behind the wall. If you live in an already fully built house or apartment, then you can create a false wall. Just sheathing everything a short distance from the radiator.

Of the shortcomings, this is a decrease in free space and a clear reduction in the room. And also the room will be heated a little worse. There will be natural difficulties, as well as costs in the event of a breakdown.

For a long time, including now, batteries are masked with heavy curtains made of dense fabric. The idea is good because it does not require extra costs and investments. And curtains are a natural part of the interior and do not attract much attention.

You can paint or wallpaper the heating pipes. This will help reduce their visibility in the room. But everything must be done qualitatively. Paint with smudges or obliquely glued wallpaper will only attract unnecessary attention and will involuntarily catch the eye.

Unusual ideas for hiding the radiator

You can get rid of all the pipes and replace them with a safer underfloor heating. The method has its advantages, first of all you will not be dependent on heating season, free space will increase, the chance that you will be doused with boiling water from your own battery will be equal to zero.

Of the minuses are the prices for electricity, the possibility short circuit, fires, etc. increases. And also in the absence of light, in winter you will have to look for another place to spend the night.

For a children's room, fabric covers for radiators are gaining popularity. Most often they are made by hand. Created in the form of a favorite character or canvas with a magical story, letters, numbers, etc.

It all depends on the age and hobbies of the baby. Such a detail will be perfectly combined with the atmosphere of the children's room and protect the child from burns and bruises.

Particularly original people hire artists. They use a battery instead of a canvas and paint on it with heat-resistant paints, creating unique masterpieces that fit the interior of the room. The advantage is the ability to draw a new drawing if you suddenly want to change the design of the room.

Heating radiators and plumbing to them often spoil the interior of the room. Especially if the room has old cast-iron radiators, completely devoid of any aesthetic appeal. Therefore, the desire of the owners to hide these elements of the heating system is understandable, but at the same time not to worsen the quality of their work. It is logical to use for these purposes an easy-to-process and affordable material - drywall. How to close pipes with drywall? How to hide radiators so that this does not affect their heating performance?

Design Options

Before you close the battery with drywall, you should analyze the placement of radiators and pipelines in the room. Depending on their location, you can choose one of two options for using drywall:

covering the battery.
A false wall that hides radiators and the supply to them behind its plane.

Options demonstrating how to close the battery with drywall with your own hands are shown in the photo below. Both methods have their advantages and disadvantages:

The installation of the box compares favorably with the smaller amount of material required. But such a design does not always organically fit into the interior of the room. In addition, pipes will have to build their own boxes, which will further complicate the task. In addition, the presence of such protrusions will seriously interfere with the installation of suspended ceilings or laying laminate on the floor.

erection decorative wall will require more material consumption, but will allow you to get a flat plane that can be easily finished in accordance with the overall design of the room. In most cases, such a structure is even easier to build than a box that closes the battery.

Construction of the box

This drywall construction can be fixed to the floor or hung with a gap above its surface. The first option is preferable - so the frame has two planes for support, which makes it stiffer.

There is an opinion that fastening with a cutter is not strong enough. However, when using professional tool the connection not only turns out to be very reliable, but also compares favorably with the absence of protruding parts, which is inevitable when using "bugs".

The required number of horizontal jumpers is mounted. The more of them, the more rigid the structure. For a drywall box, 1-2 is enough for each of the planes, with the exception of the front.
Parts of a decorative lattice or a removable screen are attached to the frame.

Need to create solid construction, any vibrations of the frame after installation are unacceptable.

On the final stage plasterboard strips are cut according to actual dimensions and fixed with self-tapping screws every 25 cm. Subsequently, the drywall is puttied, fine finishing is carried out in accordance with the general interior of the room.

False wall installation

It is advisable to erect a decorative wall if, in addition to masking the radiators, it is necessary to decide how to close the heating pipes with drywall. With this method, not so much space is lost, but the appearance of the room wins very significantly.

Additional guides will be required if there is a window on the wall: they are useful for attaching slopes. It is advisable to place a couple more profiles at a distance of 10 cm on each side of the radiator - for mounting a decorative grille.
Using a square, the marking lines are transferred to the floor and ceiling, their length is the distance from the most protruding part of the radiator (usually a tap) to the wall plus 10 cm.

In the design of the decorative wall, it is necessary to provide technological openings for access to taps and other parts of the pipeline for preventive maintenance or inspection. Such inspection hatches are subsequently decorated with a fine finish and become invisible in the general interior.

After marking, the frame is assembled. Its installation is not fundamentally different from the assembly of a box or other drywall construction, so it makes no sense to give a detailed sequence of operations. The metal frame for the false wall will differ from the box design in a large number of horizontal lintels. They are needed not only for joining drywall sheets, but also for stiffening. Experts recommend installing these elements every 60 cm, securely attaching them to the racks using self-tapping screws or a notcher.

Elements cut from drywall are attached to the frame. When deciding how to close the radiators in an apartment with drywall, you should choose a moisture-resistant gypsum plasterboard: such a wall will not suffer from condensate that forms on pipes, or in case of possible leaks in the heating system.