Verification of individual water meters. The Ministry of Regional Development proposes to introduce an increased fee for housing and communal services for citizens and companies that have not installed meters for water, electricity and heat Ministry of Regional Development water meters

Citizens who have not installed by the end of the year meters for hot and cold water, heating and electricity, from 2014 will have to pay in excess of the standard consumption. The fee will increase every six months, the relevant amendments to the legislation have been prepared by the Ministry of Regional Development. They do not apply to houses in which the installation of meters is technically impossible.

If the house does not have common house and individual metering devices, then from January 1, 2014, you will have to pay 10% more than the standard for electricity, hot and cold water, according to materials from the Ministry of Regional Development. From July 1, 2014 it will be plus 20%, from January 1, 2015 - 40%, from July 1, 2015 - 50%, and from 2016 - 60%. The same standards apply to the consumption of electricity and water for general house needs.

There is no talk of installing apartment heat meters. But if in an apartment building it is possible to install a common house meter, but it is not there, then residents will have to pay with the same multiplier.

Citizens could install meters for water and heat at their own choice until July 1, 2012. After this period, resource-supplying organizations have the right to forcibly install devices and enter their cost into the costs of maintaining and repairing housing.

According to the legislation, in the absence of meters, those who are not registered in the apartments are also required to pay for electricity, water and heat. The Ministry of Regional Development proposes to tighten this rule and oblige citizens to report their registration, as well as arriving guests or tenants within five days. An application must be submitted to the Criminal Code indicating the name of the owner and the registered citizen. In case of arrival of a guest, you must send to the Criminal Code his name and length of stay.

If the owner did not notify about the citizens temporarily residing in his apartment, then the employees of the Criminal Code, with the help of two other residents, can establish this fact themselves - even if the owner of the apartment is absent or unwilling.

The Ministry of Regional Development also proposes to make payments more detailed. In particular, expenses for general house needs should be recorded in a separate line. This provision does not apply to heat - it will be taken into account on one line and will include payment for heating both residential and all non-residential premises in the house.

The introduction of amendments by the Ministry of Regional Development coincided with a meeting with President Vladimir a, at which the head of state criticized the department for increasing payments since January 1, 2013. From that moment, the government decree on new payment calculations began to operate (they indicate the expenses of the owners and for general house needs, and the regions set their own consumption standards).

“So, as practice shows, there is no relationship between the regulation of tariffs and the real payment of citizens,” admitted the head of the Ministry of Regional Development, Igor Slyunyaev.

According to Slyunyaev, in 49 regions, citizens began to pay more. Moreover, the tariffs of resource-supplying organizations did not increase: they are now growing twice a year - from July 1 and September 1. According to Slyunyaev, the tariffs of management companies, however, increased in 21 regions, consumption standards - in 9, and in 19 regions - both tariffs and standards.

The maximum jump in prices - 225% - was noted in two municipalities in the Murmansk region.

Putin also filed a claim for payments in St. Petersburg. “In St. Petersburg, in some areas [rents] have increased by 40 percent. Here they are, bills,” the head of state was indignant. An aide to the president presented a bill for a certain St. Petersburg apartment: the fee there increased from 3,790 rubles to 12,570 rubles. In Moscow, where payments do not include expenses for general house needs, the situation is better, Nabiullina reported and presented documents for her apartment. “I had 3,900 in October, 4,900 in November, 5,100 in December, and 5,400 in January,” Nabiullina said.

“And in Murmansk, you say, in some municipalities by more than 200 percent. You've gone crazy, haven't you!" - Putin addressed Slyunyaev.

The minister tried to justify the situation by saying that management companies began to fill in the “heating” line at will: either this is a fee for heating season or monthly. “Are they paid regularly, or is it also increased during the heating season?” Putin asked.

The overpayment for housing and communal services must be returned, the president ordered. The head of the Ministry of Regional Development, in turn, put forward his own proposals to remedy the situation: to limit the growth of rent costs by no more than 10-15% per year, to oblige resource supply organizations to install meters and include these costs in investment programs, and also to create commercial accounting operators for utility bills.

The initiatives developed by the Ministry of Regional Development reflect the idea supported by both the government and the president to stimulate the installation of meters, the head of the working group of the expert council under the government for the development of housing and communal services, executive director of NP "Housing and Public Utilities Development" Andrey. “We have been preparing these amendments with the Ministry of Regional Development. Until we economically stimulate the installation of metering devices, we will not be able to calculate how much water is consumed and what losses. It is impossible to talk about modernization in such a situation, ”the expert emphasized. According to him, the problem is not who will install the meters and pay for them, but that these devices work. “We have somewhere consumption standards are overstated, somewhere they are underestimated. And where they are underestimated, in case of installing meters, the payment increases. Instead of saving and fighting leaks, the management company breaks them, ”Chibis gave an example.

Economic incentives for the installation of metering devices are correct in principle, but require the study of other issues, points out the leading legal adviser of the Institute of Economics of the city Dmitry. “The state is inconsistent and is afraid of social discontent, therefore, sanctions were not introduced for citizens for not installing meters, but there are sanctions for organizations,” the expert recalls.

“Can all 100% of consumers install metering devices by the end of the year? Will there be such a technical possibility? Are there enough metering devices? And will consumers have enough money? asks the lawyer.

He recalled that in 2010 the initiative on increased coefficients had already been discussed, but the government did not pass. In addition, municipalities have to pay for the installation of meters in social housing, but there is no money for this in their budgets, the lawyer notes.

Gordeev supports the centralized installation of meters by resource-supplying organizations, but makes a reservation: “The proposal should have been accepted a long time ago. Now it does not fit with the initiative of individual installation of meters.” “Now all residents are required to take readings within two days, and the Criminal Code is to subtract them from the data of common house devices. All residents do not submit information at the same time, the calculations turn out to be inaccurate, ”the expert explained.

The program for introducing coefficients to the standards must be built strictly in conjunction with the installation of general house meters and introduce increased standards only for houses without such meters, says Andrey, head of the sales department of Russian Communal Systems. Otherwise, according to him, citizens will install individual meters faster than common ones. “In the area of ​​activity, by now, 48% of houses are provided with general house electricity metering devices, heating - 45%, cold water — 42%, hot water- 24% (due to the absence or deregulation of hot water recirculation networks)," Maslov cited the statistics. He acknowledged that resource-supplying organizations do not have money for a one-time installation of meters.

The Evraziysky company also supports the initiative and points to the problem of a lack of common house meters in houses. In particular, in Sochi apartment buildings devices are installed in 78.54% of apartments, and common house meters - in only 7.5% of houses. “And here we have to talk not only and not so much about the lack of activity of citizens, but about their purposeful unwillingness to solve this problem,” the company believes. Sochivodokanal has not yet begun the forced installation of meters, but is already calculating the necessary costs. The difference in the readings of common house water meters and apartment meters in Sochi is 10.47%, calculated in Eurasian. “This is the average percentage of cold water losses in apartment buildings, associated both with the non-installation of meters and with the technical condition of communications,” the company noted. These losses are borne by water suppliers, management companies and homeowners associations.

Evraziysky believes that the amendments of the Ministry of Regional Development should clarify the situation in which a common house meter is installed in an apartment building, but there are none in apartments (several or all). The responsibility of the parties when accepting meters, their operation and safety should also be clarified. The company recalled that fines for non-compliance with the law on energy efficiency were introduced 3 years ago, but no court case has yet been considered.

Order of the Ministry of Regional Development of Russia dated December 29, 2011 N 627 On approval of the criteria for the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices, as well as the form of an inspection report to establish the presence (absence) of the technical feasibility of installing such devices accounting and the procedure for filling it out

FILLING OUT THE INVESTIGATION ACT ON THE SUBJECT OF ESTABLISHMENT

THE PRESENCE (Absence) OF THE TECHNICAL CAPABILITY OF THE INSTALLATION

INDIVIDUAL, GENERAL (APARTMENT), COLLECTIVE

(GENERAL) METERING DEVICES

Judicial practice and legislation - Order of the Ministry of Regional Development of Russia dated December 29, 2011 N 627 On approval of the criteria for the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices, as well as the form of an inspection report to establish the presence (absence) the technical feasibility of installing such metering devices and the procedure for filling it out

In the absence of the technical possibility of installing a meter in a residential area, confirmed by the relevant act, drawn up in the form and in the manner established by order of the Ministry of Regional Development Russian Federation dated December 29, 2011 N 627, when calculating the amount of payment for the relevant utility service, the "basic standard" is applied.

ITELMA apartment water meters are created on European equipment under license from SIEMENS, a leading manufacturer of household and industrial appliances. All our products are certified.

(WFK2 - cold water meter, WFW2 - hot water meter). Installed to account for water consumption in water supply systems of any type.

By installing apartment water meters, you will significantly save money on paying for consumed water. An important factor influencing cost savings is the choice of metering device. A reliable metering device will not require additional investments for repairs, extraordinary verification or replacement. When choosing a water meter, remember that the main operational criterion is a reliable, durable, precise work device.

What is included in the standard installation of water meters?

STANDARD METER INSTALLATION KIT INCLUDES:

• cold or hot water meter;
• connection kit with check valve;
• coarse filter (purifies water before it enters the meter);

• necessary fittings (up to 2 positions);
• metal-plastic up to 50 cm (the most flexible material that allows you to install the meter in hard-to-reach places);
• one control seal.

Standard meter installation work includes:

• pipe cut;
• installation of a standard meter installation kit;

• sealing of the metering unit;
• preparation of a set of documents with its transfer to the client.

The listed materials and works are included in the cost of a standard meter installation.

Reasons for installing water meters

By installing water meters in your apartment, everyone can count on significant savings in paying for consumed water. An average Muscovite consumes on average 3-4 m3 of cold and 2.5-3 m3 of hot water per month, and pays for 11.68 m3! half utility bill at the standard rate, citizens pay for water that they did not use. By installing cold and hot water meters in your home, you will be able to use water, paying only for its actual consumption!

Of course, the installation of water meters is a paid service, and a certain amount will have to be spent on the purchase and installation of meters, but the meters are installed for a long time, and pay off, for example, for a family of 5 in less than six months.

Another reason for installing water meters is the massive non-payments of the residents of the house. Because of this, utilities, trying to compensate for their costs, begin to “scatter” unpaid money into the accounts of conscientious payers.

The reform of the housing and communal services provides for the widespread transfer of their structures to water accounting and payment in accordance with the real, and not the average, water consumption by consumers. For example, in Moscow, since 2003, all rented houses in without fail must be equipped with apartment water meters (water meters).

Application of water meters

They are used to account for water consumption in water supply systems of any type - in individual houses, apartments, offices, administrative buildings.

Typical users are:

• individual consumers;
• operating organizations (DEZ, REU, ZhSK, HOA);
• construction organizations.

For apartment-by-apartment water metering, water meters with a diameter of 15-20 mm are usually used, as a rule, these are single-jet devices. They are the most optimal in terms of price-quality ratio.

The main differences between hot water meters and cold water meters are the use of meters made of more resistant materials and with more a high degree allowable error.

The most important characteristics when choosing a water meter are:

• connecting diameter of the pipeline (DN);
• installation length of the pipeline;
• device registration in State Register measuring instruments of the State Standard of the Russian Federation;
• water meter accuracy class;
• possible installation options for using this water meter.

The installation length of the water meter is of particular importance for single-jet models, the correctness of which is significantly affected by the turbulence of the flow. To do this, after shutoff valves, adapters, filters, a straight section of the pipeline is provided with a length of 3-5 Du in front of the water meter and 1 Du after the meter. In this regard, water meters with DN 15-20 mm and an installation length of 130 mm or more can be installed without additional pipes in front and after them.

The accuracy class of a water meter is determined by the level of permissible error with which the device can operate at rated flow power. For apartment accounting drinking water water meters of class A (±1%) for cold and class B (±2%) for hot water are allowed.

When deciding on the installation of water meters, it is important to remember that the installation and further maintenance of water meters should be carried out by specialized organizations. The professionalism of the employees of the selected organization will guarantee that the meter will serve for a long time and without problems.

The principle of operation of an apartment water meter

A water meter (hot or cold) is used to measure the amount of water that flows through a pipeline. According to the principle of operation, water meters can be divided into tachometric, vortex, ultrasonic, electromagnetic (used in industry). By design, they are divided into separate and compact. By the number of serviced pipelines, water meters are divided into single-channel, two-channel and multi-channel.

Tachometric water meters have found wide application, in the device of which there is a mechanism (tachometer), which is activated by passing a stream of water through it. The flow of water acts on the blades or on the turbines, causing them to rotate. The rotation is transmitted to a counting mechanism that sums up the water flow.

Tachometric water meters are divided into several subtypes:

• turbine
• single jet
• multi-jet

Turbine mechanical meters are used to measure the consumption of cold or hot water in water supply systems. various types, systems of automatic control, regulation and management of technological processes and other areas of activity that require accounting for consumed water. Installed at the inlets of water supply systems industrial enterprises, multi-storey buildings and in the water supply system.

Single-jet water meters are dry-running meters, the principle of operation of which is based on measuring the number of revolutions of an impeller rotating under the influence of a single flow of water in a pipeline. The rotation of the impeller is transmitted to the indicator device by means of magnetic couplings. The counting mechanism of the dry-running counter is protected from water, which ensures long-term stability of measurements.

Advantages of dry meters:

• the design of the device provides protection against an external magnetic field (antimagnetic protection of the water meter);
• all devices can be equipped with a pulse output, which provides the possibility of remote reading of readings (the pulse output module is installed inside the water meter housing).

Multi-jet water meters differ from single-jet ones in that the water flow is divided into several jets before it hits the impeller blade. Due to this, the error of the turbulence of the flow is significantly reduced.

Advantages of multi-jet meters:

• minimum labor costs during dismantling and installation during periodic verification (only the upper easily removable part of the water meter is subject to verification);
• through additional adapter sleeves, the front panel of the meter is set to the level of the decorative surface);
• all water meters can be equipped with a pulse output, which allows remote reading of readings (the pulse output module is installed inside the water meter case).

Also, water meters can be divided into wet and dry type water meters. Water meters wet type are the simplest, but, nevertheless, quite effective. The mechanism of wet type water meters is not isolated from the flow through the meter. The advantages of these meters is their low cost, the disadvantage is the high sensitivity of the water meter to water quality.

Dry type water meters do not have this disadvantage. In dry meters, the mechanism is hermetically protected from the measured water flow by a non-magnetic partition, which does not leave deposits. Transmission and fixation of readings occurs when readings are transmitted from a rotating impeller or turbine using a magnet fixed inside. A dry mechanism is often equipped with multi-jet meters for more accurate accounting of water consumption. On single-jet meters, the dry mechanism is installed less often, which leaves them the cheapest.

Combined type water meters are also used, in which both vane and turbine mechanisms are combined, placed in parallel. When the pressure in the system is low, water enters through the vane metering mechanism, when the pressure increases, the flow passes to the turbine mechanism, the vane mechanism is blocked by a valve. Usually the mechanisms are located in the same plane.

Instrument verification

Payment of utility bills individual devices accounting in accordance with Decree of the Government of the Russian Federation No. 307 of May 23, 2006 “On the procedure for providing public services to citizens”, is performed only when the mandatory verification procedure is carried out on time.

Checking and calibrating water meters are two different processes. Verification is carried out in accordance with federal law of the Russian Federation dated June 26, 2008 N 102-FZ "On ensuring the uniformity of measurements".

Meter verification is a process Maintenance individual water consumption meters (repair, warranty service). Verification is a metrological process, upon completion of which the relevant documents are issued to the owner of the meter. On average, an installed water meter can work up to twelve years, but periodically (once every four years for hot water, and once every six years for cold water), the meter must be verified. Of course, in order to reduce the cost of checking the meter, the subscriber can remove the meter himself and deliver it to the metrological service on his own, but still it is better to entrust all the processes to professionals.

Why is regular verification of water meters necessary? Since the water meter belongs to metrological instruments, mandatory verification is a process necessary to determine the errors that occur in the operation of the meter. In metrological services, an individual meter is checked for errors, adjusted to the parameters that it must comply with, and issued Required documents confirming that the work has been completed. If the verification procedure is ignored, the meter is considered unsuitable for use, and penalties may be imposed on the tenant, up to recalculation

04.05.2012

In what cases it is impossible to install water, energy and gas meters in the house? (Order of the Ministry of Regional Development of the Russian Federation of December 29, 2011 No. 627)

Order of the Ministry of Regional Development of the Russian Federation of December 29, 2011 No. 627 “On approval of the criteria for the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices, as well as the form of an inspection report to establish the presence (absence) the technical feasibility of installing such metering devices and the procedure for filling it out”
Registered in the Ministry of Justice of the Russian Federation on April 23, 2012 Registration N 23933.

From September 1, 2012, new rules for the provision of public services in multi-apartment and residential buildings. According to them, individual, common (apartment) and collective (common house) metering devices for consumed resources (cold and hot water, electricity and heat, natural gas) should be installed in the premises. An exception is the technical impossibility of such an installation.
The criteria by which it is determined have been developed. For example, it is considered impossible to install metering devices if this requires reconstruction, overhaul of existing ones or the creation of new in-house engineering systems (in-house equipment). A similar conclusion is made if it is impossible to comply with the mandatory metrological and technical requirements for the metering device or the requirements for the conditions of its operation (in particular, due to the technical condition engineering systems, humidity, temperature, electromagnetic interference, flooding).
Individual and general (apartment) heat energy meters are not installed in apartment buildings with vertical wiring of engineering heating systems.
The results of a survey of the technical feasibility of installing a meter are reflected in the act. Its form and filling order are established.
In newly built houses, the technical possibility of installing metering devices should be available in any case.
The order comes into force on September 1, 2012.

Order of the Ministry of Regional Development of the Russian Federation of December 29, 2011 No. 627 “On approval of the criteria for the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices, as well as the form of an inspection report to establish the presence (absence) the technical feasibility of installing such metering devices and the procedure for filling it out” (did not enter into force)

In accordance with subparagraph "d" of paragraph 4 of the Decree of the Government of the Russian Federation dated May 6, 2011 No. 354 "On the provision of public services to owners and users of premises in apartment buildings and residential buildings" (Collected Legislation of the Russian Federation, 2011, No. 22, art. 3168)

1. Approve:

criteria for the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices in accordance with Appendix No. 1 to this order;

the form of the inspection report to establish the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices in accordance with Appendix No. 2 to this order;

the procedure for filling out an inspection report to determine the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices in accordance with Appendix No. 3 to this order.

3. Not later than 10 days from the date of signing, the Department of Housing and Communal Services shall send this order for state registration to the Ministry of Justice of the Russian Federation.

4. To impose control over the execution of this order on the Deputy Minister of Regional Development of the Russian Federation A.A. Popov.

Registration number 23933

Application No. 1
to order
dated December 29, 2011 No. 627

Criteria
the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices

1. Criteria for the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices for cold water, hot water, electric energy, natural gas, thermal energy (hereinafter referred to as the metering device of the appropriate type) are established in order to determine the possibility the use of metering devices of the appropriate type when calculating the payment for utility services for cold water supply, hot water supply, electricity supply, gas supply, heating.

2. It is not technically possible to install a metering device of the appropriate type in an apartment building (residential building or premises), with the exception of an apartment building (residential building or premises) specified in paragraph 5 of this document, if the survey reveals the presence of at least one of criteria below:

a) installation of a metering device of the appropriate type according to the design characteristics of an apartment building (residential building or premises) is impossible without reconstruction, overhaul existing in-house engineering systems (in-house equipment) and (or) without creating new in-house engineering systems (in-house equipment);

b) when installing a metering device of the appropriate type, it is impossible to ensure compliance with the mandatory metrological and technical requirements to the metering device of the appropriate type, including the place and procedure for its installation, presented in accordance with the legislation of the Russian Federation on ensuring the uniformity of measurements and on technical regulation;

c) in the place where the metering device of the corresponding type is to be installed, it is impossible to ensure compliance with the mandatory requirements for the operating conditions of the metering device of the corresponding type, which are necessary for its proper functioning, in accordance with the legislation of the Russian Federation on ensuring the uniformity of measurements and on technical regulation, including due to the technical condition and (or) mode of operation of in-house engineering systems (in-house equipment), temperature conditions, humidity, electromagnetic interference, flooding of premises, and (or) it is impossible to provide access for taking readings of a metering device of the appropriate type, its maintenance, replacements.

3. It is not technically possible to install an individual, common (apartment) heat energy meter in the premises of an apartment building, with the exception of the apartment building specified in paragraph 5 of this document, if, according to the design characteristics, the apartment building has a vertical wiring of in-house engineering heating systems.

4. It is technically possible to install a metering device of the appropriate type in an apartment building (residential building or premises), with the exception of an apartment building (residential building or premises) specified in paragraph 5 of this document, if during the examination of the technical feasibility of installing a metering device of the appropriate type the absence of the criteria specified in paragraphs 2 and of this document will be found.

5. Regarding apartment buildings(residential buildings or premises), for which the Federal Law of November 23, 2009 No. 261-FZ "On Energy Saving and Increasing energy efficiency and on Amendments to Certain Legislative Acts of the Russian Federation” (Sobraniye Zakonodatelstva Rossiyskoy Federatsii, 2009, No. 48, Art. 5711; 2010, No. 19, Art. 2291, No. 31, Art. 4160, Art. 4206; 2011, No. 29 , Article 4288, Article 4291, No. 30, Article 4590, No. 49, Article 7061, No. 50, Article 7344, 7359, No. 51, Article 7447), a requirement is established for their equipment on the date of their commissioning certain types of metering devices for energy resources, the technical possibility of installing such metering devices is available.

6. The results of a survey of the technical feasibility of installing a metering device of the appropriate type are indicated in the survey report to establish the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices.

Application No. 2
to the order of the Ministry of Regional Development of the Russian Federation
dated December 29, 2011 No. 627

Act form
surveys to establish the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices

__________________ "__" ______________ 20__

1. ______________________________________________________________________

conducting the survey)

address (location): _______________________________________________

_________________________________________________________________________

_________________________________________________________________________

contact number: ____________________________________________________,

2. Represented by _______________________________________________________________

_________________________________________________________________________

(last name, first name, patronymic of the person - representative legal entity

(individual entrepreneur) conducting the survey)

acting on the basis _______________________________________________

_________________________________________________________________________

(details of the document confirming the authority of the person to conduct

examinations)

3. In the presence of (specify if present):

_________________________________________________________________________

(name of the legal entity (individual entrepreneur),

responsible for content common property owners of premises

in an apartment building and a person representing his interests during

examinations)

_________________________________________________________________________

(surname, name, patronymic of the owner (representative of the owner)

premises, residential building in which the survey is carried out)

_________________________________________________________________________

(other persons participating in the survey)

4. A survey was conducted to establish the presence (absence)

technical feasibility of installation _______________________________________

_________________________________________________________________________

(individual, common (apartment), collective (common house)

metering device _______________________________________________________________

(cold water, hot water, electric power, natural gas,

thermal energy)

5. Address: _______________________________________________________________

(indicate the address of the apartment building (residential building or premises),

in which the test is being carried out)

6. Examination conducted: ______________________________________________

(indicate how the examination was carried out: by inspection or

using tools / measuring instruments)

using the following tools _________________________________

(indicate the name of the instrument if it is used during the

examination, and if a measuring instrument is used, indicate it

metrological characteristics and expiration date of the next

check interval of the measuring instrument)

7. As a result of the survey, it was established: _______________________________

_________________________________________________________________________

_________________________________________________________________________

(indicate the presence or absence of technical feasibility of installation

metering device)

8. There is no technical possibility of installing a metering device due to

establishing the following criteria for the absence of such an opportunity: __________

_________________________________________________________________________

(indicate specific criteria for the lack of technical capability

meter installation)

_________________________________________________________________________

_________________________________________________________________________

9. Dissenting opinion of those present (if any): ______________________

_________________________________________________________________________

_________________________________________________________________________

_________________________________________________________________________

10. This Act is drawn up in ____ copies

Signatures of persons participating in the survey:

______________________ (____________________________)

______________________ (____________________________)

Application No. 3
to the order of the Ministry of Regional Development of the Russian Federation
dated December 29, 2011 No. 627

Order
filling out an inspection report to determine the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices

1. In paragraph 1 of the survey report to establish the presence (absence) of the technical feasibility of installing individual, common (apartment), collective (common house) metering devices (hereinafter referred to as the survey report), the full name of the legal entity (last name, first name, patronymic, passport data) individual entrepreneur) conducting the survey, as well as the contact details of such a legal entity (individual entrepreneur): address (location ( permanent place residence) and a contact phone number.

2. In paragraph 2 of the survey report, the last name, first name, patronymic of each person - a representative of a legal entity (individual entrepreneur) conducting the survey, as well as the details of the document confirming the authority of this person to conduct the survey (power of attorney, order, outfit, etc.) ).

3. Paragraph 3 of the examination report shall indicate the last name, first name, patronymic of each person present during the examination, including:

A representative of a legal entity (individual entrepreneur) responsible for the maintenance of the common property of the owners of premises in an apartment building, as well as the name of such a legal entity (last name, first name, patronymic) individual);

The owner (representative of the owner) of the premises, residential building, in respect of which an application has been submitted for the installation of an individual, common (apartment) metering device;

Other persons participating in the survey.

4. In paragraph 4 of the survey report, the type of metering device is indicated, for the installation of which a survey of the presence (absence) of the technical feasibility of its installation is being carried out:

Individual or common (apartment) or collective (common house);

Meter for cold water, hot water, electric energy, natural gas, thermal energy.

5. In paragraph 5 of the survey report, the address of the apartment building (residential building or premises) is indicated in which the survey is being carried out for the technical feasibility of installing a metering device of the appropriate type.

6. Paragraph 6 of the survey report indicates the method of conducting the survey: by inspection or using tools / measuring instruments.

If a tool is used during the survey, its name and characteristics are indicated.

If a measuring instrument is used during the survey, its name, metrological characteristics and the date of expiration of the next check interval are indicated.

7. Paragraph 7 of the survey report indicates the results of the survey, namely the presence or absence of the technical feasibility of installing a metering device of the appropriate type.

8. Paragraph 8 of the survey report is filled in if during the survey it is found that it is not technically possible to install a metering device of the corresponding type, indicating the specific criteria identified during the survey for the lack of technical feasibility of installing a metering device of the corresponding type.

9. Paragraph 9 of the survey act is filled in if any of the persons present during the survey has a dissenting opinion regarding the course of the survey and the results of the survey.

In this case, paragraph 9 of the examination report shall indicate the last name, first name, patronymic of the present person who has a dissenting opinion, as well as the content of the dissenting opinion.

10. Paragraph 10 of the survey report indicates the number of copies of the completed report, which must correspond to the number of persons present during the survey.

The drawn up acts are handed over to each of the persons present during the examination.

To exclude violation of the law when calculating the fee for utilities The Ministry of Regional Development of Russia reports the following.

Decree of the Government of the Russian Federation of May 6, 2011 N 354 approved the Rules for the provision of utility services to owners and users of premises in apartment buildings and residential buildings (effective from September 1, 2012).

According to these Rules, the volume of utility services provided for the billing period for general house needs is to be calculated and distributed among consumers in proportion to the size total area owned by each consumer (in his use) residential or non-residential premises in an apartment building. (Currently, when equipping an apartment building with a collective (common house) meter, the difference between the readings of a common house meter and the sum of the readings of individual meters and utility consumption standards (for those persons who do not have individual meters) is distributed among all owners of premises in an apartment building house, regardless of the presence of an individual resource consumption meter in the room.)

It is also reported that in accordance with the Federal Law of November 23, 2009 N 261-FZ "On Energy Saving and on Increasing Energy Efficiency and on Amending Certain Legislative Acts of the Russian Federation," owners of premises in apartment buildings are required to install metering devices for used water and electricity. energy until July 1, 2012, gas - until January 1, 2015. Failure to install such metering devices within the specified time frame is a violation of the law. Besides, apartment buildings, put into operation from January 1, 2012, must be equipped with collective (common house) and individual metering devices for all resources used.

MINISTRY OF REGIONAL DEVELOPMENT OF THE RUSSIAN FEDERATION

LETTER

dated March 13, 2012 N 5243-AP / 14

On May 6, 2011, Decree of the Government of the Russian Federation N 354 approved the changes that are being made to the Rules for the provision of public services to citizens, approved by Decree of the Government of the Russian Federation of May 23, 2006 N 307 (hereinafter referred to as the Rules). These changes came into effect in June 2011.

In accordance with the changes made to the Rules, when equipping an apartment building with a collective (common house) metering device the difference between the readings of a common house meter and the sum of the readings of individual meters and standards for the consumption of utilities (for those individuals who do not have individual metering devices) distributed between everyone owners of premises in an apartment building regardless from the presence in the room of an individual metering device for resource consumption.

Also, Decree of the Government of the Russian Federation of May 6, 2011 N 354 approved the Rules for the provision of utility services to owners and users of premises in apartment buildings and residential buildings (hereinafter referred to as the new Rules), which have not yet entered into force.

According to the new Rules, the volume of utility services provided for the billing period for general house needs is to be calculated and distributed among consumers in proportion to the size of the total area owned by each consumer (in his use) residential or non-residential premises in an apartment building.

In accordance with the Federal Law of November 23, 2009 N 261-FZ "On Energy Saving and on Increasing Energy Efficiency and on Amending Certain Legislative Acts of the Russian Federation", owners of premises in apartment buildings are obliged install metering devices for water and electricity used by July 1, 2012, gas - by January 1, 2015. Failure to install such metering devices within the specified time frame is a violation of the law.

In addition, apartment buildings commissioned from January 1, 2012 must be equipped with collective (common house) and individual metering devices for all resources used.

In order to exclude violations of the law when calculating utility bills and in order to comply with the obligation stipulated by the Federal Law of November 23, 2009 N 261-FZ "On Energy Saving and on Increasing Energy Efficiency and on Amendments to Certain Legislative Acts of the Russian Federation", please inform to the heads of all enterprises and organizations in the housing and communal sector and to inform the population.