We master the creation of a simple fountain or waterfall with our own hands. How to make a decorative fountain ⛲ on your own plot near the house, in the garden and in the country with your own hands Do-it-yourself table fountain at home

First of all, you need to preparatory work: select the location and type of the fountain.

Territory selection

The fountain should be located in a secluded area intended for relaxation, so that those present get real pleasure from being in beautiful place in an atmosphere of peace and tranquility.

practical advice

Do not place a fountain:

• nearby trees and shrubs. Over time, overgrown roots can damage its bowl.
• near the building. This can lead to mold on the wall, and, accordingly, to bad smell.
• to prevent frequent water changes due to its bloom, open sunny areas should be avoided.

The choice of the fountain itself

Pay attention to the size and variety.

The size

When choosing the size of the fountain, the shape and size of the site should be taken into account. They must be comparable. Only then will we get the necessary visual impression. In addition, the size of the fountain significantly affects the power of the selected pump, and, consequently, its cost.

Variety of fountains

The garden fountain consists of two components:

• a source of water that creates a stream;
• capacity for this water;

According to the principle of operation, garden fountains are divided into two groups:

1. Circulating Fountains. The principle of their work is that water constantly circulates in closed loop(that is, in the fountain bowl). They can work with or without a pump.
2. flow fountains. Most often they are intended for drinking water. The bowl is connected to the sewer.

How to make a fountain at their summer cottage

For example, consider the manufacture of the simplest, but quite decorative fountain circulation type. Depending on the nozzle, it may look like a fontanel, a bell, or a spray jet.

To do this, you need to perform the following sequential operations:

• purchase a round-shaped bowl of the future fountain from any material, such as plastic;
• in the chosen place, you should dig a hole in size slightly larger than the bowl itself;
• around the main pit along the entire diameter, remove a small layer of earth, approximately 10 - 12 cm to a depth of about 15 cm;
• put sand at the bottom of the pit, level it;
• insert a plastic container into the prepared pit and carefully compact the sand. The bowl is installed correctly if its edges protrude 5-6 cm above the surface;
• pour water into the bowl, but not to the very edge;
• install a pump in the center;
• carry out waterproofing over all areas of the fountain and the surface of the bowl using a special film;
• to keep the sealant stable, reinforce it with a metal mesh with small holes;
• decorate the resulting surface with crushed stone or other types of stone;
• put the desired nozzle on the pump, turn on the pump;

The fountain is ready!

The manufactured fountain has closed view(source beats from underground). But, if you slightly modify the design, then you can get a lot of options:

• if you want to have an open pond, then you do not need to cover the surface of the water surface, but decorate only the edges of the bowl;
• you can change the shape of the reservoir according to your desire (rectangular, square, arbitrarily irregular);
• to create a popular multi-stage cascading fountain, you need to increase the length of the tube and beautifully decorate it with a stone;

Designing a fountain without a pump

The operation of such fountains is based on the principle of communicating vessels. Therefore, the duration of their work depends on the volume of the vessels (the larger the capacity, the longer the work). For example, a fountain made from five-liter bottles will run for about an hour. Extending the operation of the fountain is simple: you need to swap the lower and middle containers.

We prepare the necessary elements for work:

• two containers of the same size and shape (you can use large plastic bottles with lids);
• a bowl for a future fountain (it can be a plastic basin, a wide mug, etc.)
• thin silicone tubes;
• glue - sealant;
• decoration materials (stones, small flowers in pots, shells, etc.);

Main stages of work:

• drill two holes in the cap of each bottle. The diameter must be less than the thickness of the tube;
• insert the tubes into the holes. One should reach the bottom of the container, the other - near the lid. Carefully process with glue;
• pour water into one bottle and place it over an empty bottle;
• make a hole in the bowl, connect with a tube to the bottom bottle, grease everything thoroughly with glue;
• place the bowl over a full bottle;
• the result was a design: at the bottom - an empty bottle, in the middle - a full one, at the top - a bowl of a fountain;
• decorate according to your desire and imagination.

Making a home fountain

Nowadays, it has become very popular to have a small fountain in your home. According to the laws of ancient Chinese teachings, fountains are specially placed indoors to ensure prosperity and abundance to its owners. In addition, the sound of running water has a calming effect, promotes relaxation and rest.

Is it possible to make a home fountain with your own hands? Of course - yes!

In order for the creative process to bring you real pleasure and joy, you need to carefully prepare for it.

Required to purchase:

• regular pump for aquarium;
• silicone tube for the pump;
• glue - sealant;
• the basis for a fountain in the form of a vase, planter, flower pot or an ordinary small basin (the main condition is tightness);
• decorative stones large and medium sizes, shells and other elements of your choice;
• upper tank. As it is used specially prepared (that is, drilled) jugs, plates, etc .;

Manufacturing method:

• install an aquarium pump into the bowl of the future fountain using glue or special suction cups that come with the pump;
• insert the silicone tube into the pump in a strictly vertical position;
• lay out the prepared decor elements in the form of a slide, leave the end of the tube open;
• attach the upper decorative tank to the tube;
• pay special attention to sealing and structural strength (due to glue).

Regardless of the type or shape, any do-it-yourself decorative fountain will delight you and everyone around you.

Now many have a desire to have (especially in summer) a small fountain that would make the atmosphere more exotic. But many are sure that this idea is beyond their means. At home, you can try to realize this dream. Homemade can be done in a few hours, even if you have never created such things.

Such products are divided into indoor (decorative) and yard, arranged in suburban areas or in the courtyards of multi-storey buildings (if they do not interfere with garages, etc.). There are many different designs of home fountains. Consider how to make at least a small indoor fountain with your own hands. To begin with, we will think over the future design according to the following parameters:

1. Desired sizes.
2. The form.
3. The number of cascades in your fountain.
4. Proper design of the closed water system of the product, otherwise the fountain will not work normally.

So you have passed the first stage, and you have a drawing of your fountain on paper. Now comes the next stage: you need to prepare materials and parts for the assembly you invented. Here is a rough list:

1. Small. If you are planning to make a desktop version, then you can use an aquarium pump-pump.
2. Hermetically sealed container made of metal or plastic. For these purposes, you can adapt any dishes available in the house (vase, plastic bucket, basin).
3. For decorative design you can use pellets, shells, decorative colored glass, etc.
4. Electric cords, sockets for connecting the pump.

Self-made fountain at home

The assembly begins with the installation of the pump on the bottom (bottom) of the container you have chosen. To do this, you can use synthetic adhesives or suction cups (if an aquarium pump is used, they are included in its kit). The rise of water to the upper level is carried out using a tube (plastic, silicone). We put it on the outlet of the pump and fix it strictly vertically. Further, in order to mask the pump and isolate it from the external environment, it is necessary to close the equipment with a home-made or purchased, suitable-sized frame. If you are going to make it yourself, then do not forget to prepare the materials and tools you need for this.

If you have a plastic box with dimensions suitable for the pump, then by cutting out ventilation holes, use it as a casing. In extreme cases, you can shove the pump under a layer of colored pebbles. Next, you need to turn on your imagination, since the final result depends on it. We take any tank we like (a beautiful mug, a large sink, a plate, etc.)

It must be installed on some elevation.

This can be achieved by creating a slide of stones with your own hands, on which we mount our decorative tank with epoxy glue, into which a tube is inserted from the output end of the pump.

If there are no stones, then you can make cubes from foam or use ready-made plastic ones. To do this, we drill a hole in the vessel we have chosen according to the diameter of the tube, which is inserted into the tank (into its internal cavity), by 6-12 mm. We seal the hole and fix all the elements with our own hands, using waterproof glue and sealants.

For those who want to update the exterior, make it special and memorable, we suggest using a small homemade fountain. Step-by-step instruction making a fountain with your own hands is quite simple and anyone who has a certain set of tools and materials can create this beauty in their yard.

We install a fountain in the country

The first point of the fountain installation plan is planning its size and type. Consider the size of the yard, do not make the fountain too big or small - this will not give a positive visual effect. Remember, the power of pumping equipment is directly proportional to the size of the structure.

Now you have to choose right piece of land for installation. Firstly, the fountain should be located where it will be clearly visible. Secondly, it should be close to the place of rest. The sound of running water and cool freshness in the summer heat are important components of a pleasant and peaceful outdoor recreation. Try not to install the fountain in the open sun. Water will have to be changed frequently due to its flowering. There is also no place next to the construction trees, the roots can damage the thicket and for repairs you will have to disassemble the entire decor element.

To install a fountain with your own hands on the site correctly, do not choose places near the walls. In this case, the structure will not avoid acquaintance with mold and fungus. And this, in turn, will not only spoil appearance, but will also cause an unpleasant musty smell.

Plan ahead for future buildings on the site. Do not install a fountain on the road to them.

Do-it-yourself step-by-step guide for installing a fountain in the country

Let's talk about how to make a fountain with your own hands using the example of a very simple design - fontanel fountain. This type of building has several advantages:

• Effective appearance;
• Easy care;
• Easy access to parts for the purpose of repair;
• The possibility of parsing for the winter.

Having picked up a place for installation, we dig out foundation pit slightly larger than a fountain bowl. Additionally, a shallow hole should be dug around it. gutter(about 10 cm).

Do-it-yourself fountain. Instructions in the photo

At the bottom of the pit should be sand cushion 15 cm thick. This will protect the underground part of the structure from plant roots. We level the surface and install on it plastic bowl. We set the font according to the level, pour and ram the sand. The container should be installed in such a way that its edges protrude by 5-8 cm.

The next step is to fill the plastic container under the bowl with water. It is not necessary to pour “with a slide”, leave 4-6 cm to the edge.

Now you need install a fountain and check the operation of pumping equipment. If power pumps can be adjusted, then we adjust so that the water falls back into the bowl. Approach to the choice of equipment should be very careful. Ideally, at the time of purchase, explain to the seller what bowl size and bowl volume is expected. Then he will help you choose the equipment of the required power.

Do-it-yourself fountain. Instructions in the photo

After installing the bowl and pump, you need to do waterproofing fabric. Cut out the canvas with a diameter of a hole for the fountain. Starting from its center, cut into strips. This must be done so that the diameter of the resulting inner circle is equal to the diameter of the bowl of the structure. We bend the resulting strips of material and lower them into a container. You can fix them with a sealant. Do-it-yourself fountains always require a lot of patience and accuracy in work, especially this stage of construction.

So that the base of the structure does not lose its shape and is stable, we put a couple of rods on the sealed fabric fittings, and on top of them - galvanized fine mesh. The cell size will affect the size of the stones or rubble used. used in the decor of the fountain.

Do-it-yourself fountain. Instructions in the photo

The final stage of construction - decoration designs. The border of the fountain can be laid out with larger stones, but you should not make it too clear. Small stones like sea pebbles or gravel are laid out on the grid. If you want to add a natural fountain, then its boundaries should not be too clear. Various plants will look good along the edges of the structure.
Thematic japanese fountainfor lovers of oriental exoticism, it is installed in a similar way. Step-by-step instructions for making a fountain with your own hands for the garden in Japanese style consists of the same items. You will find a diagram of the structure below.

Do-it-yourself waterfall fountain

We will not build anything grandiose, but small, about 1 m high, cascading waterfall we are quite capable. It has already been described in detail above how to prepare a foundation pit for a pond bowl. But this time we are building a waterfall. And if there is no natural elevation for him, he will have to create it himself.

Do mound convenient in the process of digging a pit. We just throw off the ground where the hill should be, and carefully ram it. For the hose supplying water to the point where the water falls, make a small groove in the wall of the pit and embankment.

Do-it-yourself waterfall fountain. Instructions in the photo

After the foundation pit and the base of the waterfall are ready, we begin to cover the bottom and walls of the mini-pond waterproofing material(for example, PVC film). It is necessary to lay the canvas in such a way that it not only completely covers the bottom and walls of the pit, but also protrudes about half a meter on the sides of the pit.

Be sure to lay a pipe for supplying water to the top of the waterfall in a pre-prepared channel-ditch. Bend one of its edges 30-40 cm up.

This time we are making a permanent structure, and therefore it is best concrete pond bowl. To begin, carefully lay out metal mesh at the bottom of the pit. Do not allow the waterproofing to be damaged. Next, pour a layer of concrete with a thickness of about 12-15 cm.

How to make a fountain in the country with your own hands. A photo

Now you need to prepare bowl walls. We lay out the grid, strengthening it in a solution that has not yet hardened. You can continue to install a fountain with a pump with your own hands, which will look like a cascading waterfall, in a day. We fill the walls of the pond bowl and finish the most difficult stage of construction.

The next part of the build is decoration the resulting structure. We build steps on a pre-rammed hill. The step should be about 30 cm and three ledges will be enough.

On the resulting flat surfaces posting flat sandstone, pebbles or any other material you like. We decorate the rest of the fountain, including the film around the perimeter, with stones, rubble, marble or other pre-prepared materials.

It remains only to turn on the pump and fill the font of the structure with water. We observe how the stream falls steadily down the steps of the waterfall and enjoy the originality of our suburban area.

DIY stone fountain

How to build stone fountain? We will talk about this right now. First you need to take care of the availability of all necessary devices and materials. We will need:

• Water pump (underwater with medium power is suitable);
• Plastic container for a bowl;
• Tube made of metal or PVC for holding an electric cable;
• Coupling;
• Flat stones and gravel;
• Bars of wood;
• Water flow power regulator;
• Copper tube with a diameter of 15 mm.

foundation pit for the bowl of the fountain should be a little more than the capacity prepared for these purposes. By filling the space between it and the walls of the pit with soil, we will significantly strengthen the position of the bowl. As in previous cases, do not forget to create at the bottom of the pit sand cushion. Lay a layer on top pebbles.

Water pump located freely in the water tank. This will make it easier to repair it if necessary. From debris, the water tank can be secured by a simple fine mesh. To give structural strength on top of the metal mesh are placed wooden blocks (if desired, they can be replaced with metal fittings).

The base of the fountain will be metal pipe which is attached vertically to the pump.

The next step is preparation flat stones. To do this, using special tools, we make holes with a diameter slightly larger than the diameter metal pipe- Foundations of the structure.

Further, according to the principle of the children's pyramid, we “plant” the stones on the pipe. It remains only to add decorative elements to the fountain and connect the pump. A very simple, but spectacular and beautiful do-it-yourself fountain in the country is ready for use.

A variety of do-it-yourself fountains on personal plots

Submersible fountains

If there is already a pond in the yard, then it can be used as a basis submersible fountain. The principle of its work is simple. Water is supplied by a pump directly from the pond. In this case, to install a submersible fountain, you will need:

• Pump;
• Pipe for water supply;
• Appropriate nozzle for shaping the water jet and setting it in the right direction.

Nozzles are very different. For example, bell nozzle is a two-disk design. The flow of water passes between them and changes when the gap is adjusted. Nozzle " geyser” - a tube narrowed to the top - quite effectively copies the corresponding natural phenomenon.

Such structures have quite a lot of possibilities. For example, you can create the effect of a key beating out of the ground. To do this, do-it-yourself fountain is mounted in such a way that the end of the pipe does not protrude above the surface of the reservoir.

Using more complex nozzles, you can significantly expand the possibilities of decor. The effect of spraying water, the simultaneous combination of several nozzles and many other variations for the choice of those who design a fountain in their country house.

Stationary fountains

A fountain of this type is a real find for lovers and professionals of design art. Structures can take the form of natural stone fonts, antique structures; they are made from clay pots, plastic bottles and any material that is at hand. Particularly popular in recent times fountains for Japanese gardens.

Any frost-resistant material will do: marble, fake diamond, sea pebbles and more. To decorate such fountains, they often resort to painting. There are two ways to do it:

• Staining of the material before the manufacture of the structure;
• Painting of the finished figure.

The first option is much more expensive, but it is also much more reliable. To protect against moss, fungus and mold, it is useful to treat the fountain structure with special means.

Small stationary fountain will look good in family recreation areas or close to playgrounds. Our master class "Do-it-yourself fountain in the country" will help novice designers to correctly build, perhaps, one of the main elements of decor in a suburban area. And it doesn't matter if it's a small fountain-geyser or a large-scale cascading waterfall 2 meters high. The main thing is that he pleases the owners and does not cause problems.

Video instructions for making a fountain in the country

Who said that a fountain is an exclusively outdoor fixture? Modern decorations of this type are used with equal success both outside the house and indoors - everything is decided by the size and device. For apartments and houses, as a rule, apply small size fountains, which are called "home fountain". It is about them, or rather about their options self-manufacturing will be discussed in this article.

A person can contemplate three things for a long time - for a long time he is not able to take his eyes off the flame, the flowing water and how someone else is working. It is for this reason that the most common decorations in houses and apartments are all kinds of fireplaces and fountains. In this article we will talk about fountains - together with the Dream House website, we will deal with the question of how to make a home fountain with your own hands? We will consider various options for the independent manufacture of this decor, and most importantly, we will deal with the principle of creating such things, the knowledge of which will allow you to independently design these products at home.

Do-it-yourself home mini-fountain photo

Home fountain: how it works

Most of you will probably be surprised at how simple a fountain is - you could even say that by the standards modern technologies this is an elementary thing that does not cause difficulties in manufacturing at all. If you deal with its design, then it can be divided into just a few separate parts. Plus or minus, of course, since there is no limit to perfection, and you can improve it, as they say, to infinity.

As for the principle of operation of such devices, there is nothing special to understand here - the movement of the liquid simply loops. There is a container from which the pump pumps out water and delivers it to the fountain nozzles - flying out in the form of a beautiful decorative jet or flowing down a waterfall, it returns back to the same container, from which, again, it is sucked in by the pump and sent to the next ring cycle. That's the whole fountain.

How to make a fountain at home: options

Among the most common options for making home fountains with your own hands, you can select just a couple of more or less successful designs. To be honest, only one is completely successful - the first variation, although acceptable for a house or apartment, still has several significant drawbacks.

Depending on the required dimensions, intermediate containers can also be installed - to create a so-called cascade of waterfalls, which will look much more attractive. The principle of making such fountains is no different from a single waterfall - the only thing that is added here is one or more intermediate containers. In such a situation, the pump pumps water into the upper tank, from where it flows by gravity into the reservoir located just below. In turn, water will flow from this reservoir into a container located below - with this approach to business, the number of containers can be unlimited.

home fountain photo

How to make a home fountain with your own hands: installation without a pump

I’ll make a reservation right away that this is not a perpetual motion machine, and such a fountain will not be able to work indefinitely - this is an excellent toy that clearly demonstrates the work of the laws of physics and nothing more. Depending on the containers used in the design of such a fountain, you can count on 10, 15 minutes, maybe even half an hour of operation time - then you need to recharge, which you will get tired of doing in the very near future.

We are talking about, for the operation of which three containers are required, connected in series with each other by tubes - this is a completely sealed system that works thanks to an air lock. From the receiving bowl, water enters the lowest, and most importantly, empty container - it presses on the air in it, which, in turn, creates pressure in the upper container (it is filled with water). It is this pressure that causes the water to rise upwards. What is most interesting, the rise of the jet can be quite large and reach 1m in height. Moreover, this fountain can even be somewhat "automated" - to organize its recharging with less time and effort spent. Undoubtedly, this is a noteworthy invention of mankind, to which it is worth devoting a separate article, which we will do in the future.

How to make a home fountain with your own hands: Heron's fountain photo

In conclusion of the topic of how to make a home fountain, a few words about very attractive additions that will allow you to contemplate not only the view of flowing water, but also observe various effects. The very first thing that comes to mind here is . You can organize it different ways, but the most interesting of these is the use of a small electric generator. A small device bought in a store is quite capable of making the LEDs glow - you can arrange them any way and anywhere, the main thing is not to forget that water and electricity are incompatible things in principle.

Even the smallest pond is able to decorate your own summer cottage and give it a twist. And a do-it-yourself fountain will not only become a favorite place to relax and provide aesthetic pleasure, but will also become an occasion for compliments from invited guests.

But not everyone decides to build this mysterious hydraulic device with their own hands. Some summer residents mistakenly believe that the construction of a fountain is a laborious and expensive process, and one cannot do without the help of specialists in this matter. But every fan of spending time in nature can give himself such pleasure, the main thing is to know all the nuances of building a fountain with his own hands.

SELECTING THE TYPE OF THE FOUNTAIN

There are two types of fountains according to the type of construction.

1. The open version involves the supply of water to the nozzle. The formation of a jet in this version of the device occurs due to changes in the water level. The water pressure in this case is weak, so it is necessary to constantly monitor the water level. In addition, the water in such a fountain quickly becomes contaminated. To create it, you need to install a small tank at a height of about one meter above the nozzle.
2. Fountain with pump installation - the most practical and spectacular option. Thanks to the placement on the bottom of the pump, continuous circulation of water is ensured. Here, the pressure is stronger and the visual effect is more beautiful.

By design, pumps that act as fountains are divided into submersible and surface (stationary).

THE OPTIMUM PLACE FOR THE FOUNTAIN

When choosing a convenient place for the construction of a fountain, it is recommended to take into account the degree of slope of the earth. If the plot is uneven, it is better to place such a decoration in a lowland. This option for the location of the reservoir will allow not only to adjust the volumes ground water, but will increase the oxygen saturation of the air.

• too close to the house so that moisture in windy weather does not get on the walls;
• in open areas, in order to prevent water from blooming due to sunlight on the reservoir;
• next to the trees so that the leaves, seeds, fluff falling from them do not clog it, and the roots do not damage the waterproofing.

The fountain should be located in such a way that it is not an obstacle on the way to other buildings and is visible from all points. It is recommended to place the structure near the resting place.

The minimum distance that must be maintained between the fountain and plants, buildings, furniture is 50 cm. So the plants will not die from excessive moisture, and the furniture will not become unusable. The ideal option for the location of the fountain is partial shade and a place protected from the wind, located in close proximity to a source of water and electricity. This arrangement will save you from unnecessary wires and additional work on their insulation.

Having decided on the place, it's time to think about the shape and depth of the future fountain.

PREPARATION OF MATERIALS FOR CONSTRUCTION

To build a fountain in order to save money and effort, you can use the construction technology ornamental pond with the equipment of his pump.

Materials needed to build a fountain:

• fountain container;
• pumping station;
• durable film;
• bayonet shovel;
• natural stones of various sizes;
• sand, gravel;
• decorative elements.

TANK SELECTION AND INSTALLATION

If you plan to build a miniature fountain, you can use an ordinary plastic basin or any other small container as a reservoir.

For large reservoirs, old bathtubs or a self-dug pit are suitable. If a bath is used, it is necessary to dig a hole of such a size that its edges are not higher than the ground. All holes are securely sealed in the bath, after which it is lowered into the pit and strengthened with earth, stones and sand.

For a home-made tank, they make a hole of the required depth and cover it with a dense, high-quality film, which is fixed along the edges on the surface with stones. Stones of various shapes and sizes are also poured to the bottom. It is important that the stones do not have sharp edges and cannot cut through the film. The stones are evenly distributed over the entire bottom of the future fountain.

SELECTION OF A PUMP FOR CONSTRUCTION OF A FOUNTAIN

In order to construct a fountain on the site on your own, it is not necessary to purchase expensive materials, you can adapt any old elements. However, you should not spare money - the pump, the better it is, the more beautiful the fountain will turn out and will decorate the site for longer without causing problems.

Submersible pump - best option for the construction of a fountain at their summer cottage. Works on the principle of a centrifuge. You can also install a surface pump, it is mounted on the edge of the reservoir, but is most often used on large fountains and cascading reservoirs.

When choosing a pump, it is worth starting from the pressure that is constantly present in the pipe and the differences in this pressure. Therefore, buying the most powerful pump may not be justified, since not in all cases it will be able to work out its full power.

Regardless of which type of pump is chosen, it is important to remember that its power must be related to the diameter of the pipe. The jet of the fountain should come out under powerful pressure, and not slowly flow out of the pipe, since there will be no effect from such a design.

HOW TO MAKE A FOUNTAIN WITH YOUR HANDS: A STEP-BY-STEP INSTRUCTION

The construction of the fountain includes several main stages:

• pit preparation;
• fixing the trench;
• installation of a container or covering the bottom and edges with a film;
• installation of pumping equipment;
• fountain decoration.

FOUNTAIN WITH A POND FROM AN OLD TIRE

To build such a fountain you will need:

• old tire from truck or tractor;
• cement mixture, water, crushed stone and sand;
• container for mixing cement and a shovel;
• sealant;
• building level;
• mastic;
• stones;
• pump.

Stages of work:

VIDEO - FOUNTAIN FROM THE TIRE WITH YOUR HANDS

FOUNTAIN FOR COTTAGE USING FILM

For such a fountain you will need to prepare:

• thick film;
• shovel;
• sand;
• pump;
• stones of different sizes without sharp corners.

Stages of work:

• we dig a hole, clear it of stones and tamp the bottom;

NEW LIFE FOR AN OLD BATH

For this version of the country fountain, you need to prepare:

• shovel;
• pebbles;
• pump equipment;
• bath;
• insulating tape;
• metal scissors;
• colored iron sheet;
• drill.

Stages of the construction of the fountain:

• we dig a pit corresponding to the size of the existing container;
• we put the bath inside and plug all the holes;

• we cut out wide strips from iron and lay them around the bath, close them with stones;

MINI FOUNTAIN FROM A PLASTIC BOTTLE

For this sprinkler you will need:

• plastic bottle;
• metal, strong wire or nail;
• insulating tape;
• garden hose.

Materials for a decorative fountain

Construction stages:

• decorate the pot with paints;
• make a small hole in the bottom of the pot;
• install a pump under the pallet;
• we drag the pump tube through the hole made in the pot;
• we fill the bottom with pebbles;
• decorate artificial plants and figurines;
• fill the pot with water.

VIDEO - DECORATIVE FOUNTAIN OWN HANDS

FOUNTAIN DECORATION

You can emphasize the uniqueness of a handmade fountain by decorating it. It is recommended to lay out beautiful, multi-colored stones of different sizes around the reservoir, put flowers in pots, place cute figurines of animals, birds, and so on.

To make the fountain amaze with its beauty and unusualness at night, you can make a backlight using special equipment. Lamps installed around the perimeter of the fountain and lighting at its bottom will create a fabulous, magical atmosphere.

The bottom of the reservoir can be planted with special plants, bushes can be planted around the fountain.

Any country pond and fountain, including, needs careful care. To maintain the order and transparency of the water, a pleasant spring appearance of the structure, it is necessary to regularly clean the tank. With the help of special devices, it is required to remove leaves, seeds, fluff and other objects from the surface of the water that can not only spoil the appearance of the reservoir, but also lead to a malfunction of the fountain.

At the end holiday season it is necessary to drain all the water, transfer the removable parts of the structure to a closed room, and cover the remaining parts and the bowl with a film so that dirt does not get into them.

Building a fountain with your own hands in a country house or even in an apartment is not difficult and does not require large financial resources. Before building a decorative fountain, you need to decide on the shape, size and installation location. There are many options for the location of such structures - at the gazebo, on the lawn, in the garden. After the construction of the fountain, you need to carefully monitor the purity of the water, regularly remove debris and add water, as it will evaporate.

Such designs are widely used in the design of suburban areas. Fountains can decorate any abandoned area or become a highlight suburban area. And by connecting fantasy and decorative elements, you can make it even more beautiful and unusual.

landscape design