Creative table lamps with your own hands. DIY chandelier from improvised materials: detailed master classes

There are all sorts of lamps in electrical goods stores - manufacturers go to all sorts of tricks so that each buyer finds exactly what suits him both in design and in his pocket. But a hand-made sconce is still the most original functional home decoration.

Electricity and creativity

Electrical appliances require the manufacture, installation and operation of compliance with all the rules that are prescribed by law, safety standards and the laws of physics. Therefore, if there is no special knowledge and skills in working with electrical appliances, then it is best to use the base from an old sconce for creativity, at least its electrical filling. To assemble a wall lamp, as they say, from scratch is only possible for someone who understands the materials, tools for collecting such equipment, knows the section of physics called "electricity", knows how to assemble electrical circuits, corresponding to the requirements for household appliances lighting. If all knowledge about this sphere of life comes down to a successfully forgotten school physics course, then it’s not worth the risk. It is better to use that wall lamp that has been asking for a trash heap for several years. Different types of creativity and craftsmanship allow you to create a sconce with your own hands. A photo similar works presented on this page. Therefore, the question of how to make a sconce with your own hands does not require a complicated answer, you just need to turn on your imagination.

Plafond for sconces - the essence of the lamp

Wall sconces perform an interesting functional task - lighting a small area of the room. They are located on the wall, and most often the light from the sconce falls down, slightly scattering on the sides. That is why wall lamps are popular for creating comfort in the bedroom, in the kitchen above the table where the whole family gathers, near the seating area with an armchair or sofa. Such a local lighting device can have any design in any style - from eco-style to hi-tech. Only the interior of the room decides what the sconce lamp will be like. Therefore, for man-made wall lighting, you can use a variety of materials. The only condition is that they must be resistant to enough high temperature light bulbs at work. Although, thanks to modern LED lighting devices, this question disappears by itself - the LED bulb during operation heats up to 64 degrees in the lower part, where the necessary lamp elements are located. The flask itself heats up to approximately 33-34 degrees, i.e. you can easily hold it in your hands. That's why LED lamp allow you to use almost any material for the ceiling. Having thought about making a sconce with your own hands, you can refer to materials in available sources or print publications to choose suitable option and for your creativity.

Threads and weaving - a suitable basis for creativity

Different types weaving from threads: macrame, tatting, knitting, crocheting, on a fork - are actively used by needlewomen to decorate the interior of their home. Creating a lace sconce with your own hands for a craftswoman is not a problem, you just need to find a suitable scheme or develop it yourself. In preparation for work, you should first consider the basis of the ceiling. Will the lace be stretched or will it hang down, what shape is the ceiling and how to put the lace on it: observing the pattern, or will it be abstract, or undemanding to a clear correspondence to each rapport. Lace will look very elegant on a rounded ceiling of a classic shape. And for a non-trivial solution for a do-it-yourself sconce lamp, lace can be appropriate. For example, for a high-tech style, you can use Lurex or metallic threads. But even those who do not know how to knit will make a lace sconce with their own hands, using ready-made lace. Measure the area of the frame for the ceiling and buy the required amount of the material you like with a margin for some shortcomings or unforeseen circumstances in the work - and an interesting, unusual lamp will decorate the room. In general, beautiful lamps are always obtained from threads. Even the chaos created from textiles can be presented in an unusual way, for example, by winding threads around a balloon, having previously coated them with PVA glue. When the threads dry, the ball must be gently blown off by piercing with a needle. The resulting spider sphere is used as a lampshade for a lamp.

wood and light

Wooden objects look very original in any interior. Natural wood is beautiful - with its pattern, shades and color transitions. Using the natural bends of branches, you can get interesting items and their details. How to make a wooden sconce with your own hands? You can use several options. For example, you can take special blanks that are sold in stores for creativity. They are assembled or glued together, forming a ceiling for the lamp. You can try to make an unusual sconce from the most ordinary twigs collected during a walk in the park. Rinse small, 1.5-2.5 cm long twigs, clean them of dirt, and dry. Then inflate an ordinary balloon and stick branches on it in a chaotic manner using glue that does not destroy the rubber of the balloon, for example, building PVA. When the branches are well grasped, the ball must be pierced with a needle, it will deflate and fall behind the resulting ball of branches. The ceiling, if necessary, is covered with furniture varnish. The only thing is that it will be necessary to prepare the base on which the ceiling of the resulting diameter is attached. A lamp on the wall with your own hands can also be made from unusual wooden parts. For example, by disassembling wooden clothespins for spare parts. They are assembled together so that they form a circle, gluing to the base and to each other. Each half of the clothespin has an interesting shape with recesses that are just perfect for jute cord or decorative braid, chain, or any other material that is most appropriate for a particular interior solution. You can also use colored pencils - creating a chaotic lamp-ball or gluing them into a slender circle or semicircle to form a ceiling.

Sconce with your own hands from dishes?

Craftsmen just do not come up with something to create something interesting. For example, they use disposable plastic utensils - junk cheap material - to create interior items, including sconces, with their own hands. Plastic spoons, cutting off their cuttings, are collected in the shape of a flower, gluing them together in circles and in rows. Disposable forks, also without cuttings, are assembled, like a designer, with the help of cloves into a sphere for a ceiling. The plates are bent, getting two semicircles, and also fastened together. This is an interesting do-it-yourself sconce solution, which is actively used in decorative art.

And you can not throw away!

Unusual wall lamps are obtained from tin cans. Banks themselves already represent a rigid form that is easily suitable for a ceiling. You just need to decorate it. You can do this like this - draw a pattern on the bank like a dot painting and use a nail and a hammer to punch holes according to the pattern. So that the jar does not wrinkle when they work on it with a hammer, you need to put a wooden block inside it. The drawing should be built neatly, and the distances between the holes should be the same. When the drawing is completed, the jar needs to be painted.

An unusual do-it-yourself sconce is obtained from ordinary plastic bottles. They come in different colors, are easily cut with scissors and melted with a candle. Figures (flowers, butterflies, ribbons) are cut out of plastic, melted, shaped, and then glued to the base from the same bottle or to an old glass ceiling with glue. By the way, lost appearance the glass ceiling can be decorated in any way and give it a second life.

"Delicious" sconces with their own hands

A lot of interesting things can be done using natural materials. For example, pumpkin. Yes, you can create magic yourself, without a fairy wand, if you just want to do something with your own hands. And the pumpkin is just asking for a desktop. There are varieties of pumpkin that can only be eaten, and there are those that are not very suitable for delicious dish, but the hard shell serves as a unique creative material, for example, to create a DIY wall lamp. The pumpkin is prepared for processing, and then pictures or a mandala drawing are cut out of it, whatever you want. Such a lamp for wall lamp will not only decorate your home for Halloween, but also give a smile on any other day.

Easy peasy

The simplest sconce lamp can be made from an ordinary box, for example, from juice or milk. It is good when such a package is covered with a layer of metallized foil from the inside, which is the best suited for creating a lamp. From such a box, an original sconce will turn out if you cut out the walls in it and tighten them, for example, with parchment paper or lace fabric, or make plot pictures on the walls of the box. Such a lamp is suitable for a children's room, because a kid can come up with a picture, and parents will help cut it out. Joint creativity will make the room more comfortable, and the family more friendly.

If there is a desire to needlework, decorating your world, then there will always be materials for creativity, and interesting solutions. You just need to want to create beauty with your own hands. Good luck!

Handmade items fill the house with special warmth and comfort. Plus, they are exclusive. We offer an overview of lamps that will completely change the atmosphere in the room, turning into an object of envy from the groans of friends and relatives. Moreover, they are made from everyday items that are usually thrown away.

A cardboard bag for juices or other drinks is a common thing in most homes. Most of the time it gets thrown away. But the Malay designer Edward Chu spent a lot of time to cut them into hundreds of strips and build amazing lamps from them without a drop of glue, a simple origami principle.

Yaroslav Olenev proposed to make lamps from disposable plastic spoons and became the winner in the nomination "Ecology and Design" from the magazine "Future Now".

No less original application was found by Natalie Simpson for ordinary wooden hangers. But they look amazing in the form of a chandelier.

Kevin Chempeny must be given credit, not everyone has the strength and patience to string 14 thousand bears to get a chandelier.

Tira Hilden and Pio Diaz have their own vision on the problem of housing lighting. Thanks to their lamps, the room becomes like a forest. All walls come to life and turn into trees.

Talented welder Matt Ludwig was also an excellent designer. For JJ's Red Hots restaurant, he made an incredibly original chandelier from an old drum set.

Texan artists Joe O'Connell and Blessing Hancock made stunning lamps from old bike parts and hung them in a tunnel under the track.

It will probably be difficult to find a more original chandelier than a pumpkin from a Polish artist. It carves stunning patterns on the peel that do not repeat.

Felt hat lampshades from Jeeves & Wooster look original and stylish.

Once Heather Jennings saw an amazing Rhododendron chandelier in the store, only it cost more than $ 800. Then the designer decided that she could do just as well with her own hands. To do this, she needed paper molds for cupcakes.

11. Chandelier in the kitchen

A chandelier made of ordinary metal tetrahedral graters will look incredibly beautiful.

Still fresh in my memory are vases and candy bowls made from openwork napkins. Now it's time to knit chandeliers.

A strange option is offered by Fansois Lego, he believes that the most The best way cutlery storage is a chandelier.

A large cloud is cut out of wood, but the rest and the switch are made of cardboard.

Several globes can make a wonderful cascading chandelier, great way illuminate the staircase.

Ceiling chandeliers - lighting devices that perform two functions at the same time. Firstly, they are used to organize the main lighting in the room. Secondly, devices are one of the main elements of the decorative decoration of the room.

Numerous manufacturers offer equipment of different designs, but it is far from always possible to find something really worthwhile that fits into the overall interior of the room. In other situations, the cost of the chandelier you like may be too high. That is why many people are interested in how to make a ceiling lamp with their own hands.

Handmade products will be unique and original, thanks to them you will be able to express your taste and character. It is not so easy to make such devices on your own. The work requires a certain imagination and perseverance. On the other hand, a ceiling chandelier can be created from improvised means and items that have become garbage for you.

Choose any materials for manufacturing - wood, plastic, metal or glass. Chandeliers made of wine bottles, wooden skewers or straw look very original. To summarize: the choice of material for a homemade lamp completely depends on the imagination and idea that arose in the head of the owner of the apartment.

Varieties of lighting fixtures

The final stage of any repair and construction work will be the purchase of lighting fixtures. Often the main one is the ceiling chandelier, which is installed in the center of the room, provided it has the correct geometry. There is a wide range of luminaires on the market that differ in design, shape, principle of operation, and even the presence / absence of certain structural elements.

Today, all people strive to save money, so it will be important to use a chandelier for energy-saving or LED lamps. It is advisable to choose products with partially or completely closed shades, in which lamps are hidden. Due to this, you will protect the ceiling structure and be able to protect yourself in the event of a light bulb explosion (the fragments will remain inside the ceiling).

If you still like a chandelier with an open arrangement of light bulbs, then inspect it and make sure that after installation the luminous flux will be directed downwards. There is also a simple rule - the simpler the product, the easier the subsequent installation.

Another point to consider when choosing a chandelier is the purpose of the room and its dimensions. In spacious rooms with high ceilings, volumetric pendant-type lamps should be installed. For small spaces, space savings are required, so focus on flat (flattened) options.

Conventionally, chandeliers for the ceiling can be divided into two main varieties:

classic hanging;
flat with the closest placement to the ceiling.

And the latter are divided into two subcategories - built-in and overhead. Overhead ceilings are considered best solution for bathrooms, corridors and kitchens. The presence of a separating platform ensures their rapid cooling and high fire and electrical safety.

Recessed lights are also called spotlights. They are often installed (more correctly, they are built in) in furniture, dropped ceilings or arch structures. Manufacturers provide a wide variety of shapes, colors and design solutions for both traditional and flat luminaires.

Finally, in addition to design features the fixtures themselves, distinguish between the type of light sources used:

The filament lamp is one of the most common and simple options. The cheapest light source. Under mechanical action, it quickly fails due to the vulnerability of the structure, burns out relatively soon (in the case of continuous operation, it can burn out in two to three days).
An energy-saving fluorescent lamp is one of the best varieties of housekeepers. Advantages of a product are connected with profitability and long service life. Along with LEDs, it is the most common light source in developed countries.
The LED lamp is an expensive product, the popularity of which is increasing every year. The efficiency factor exceeds 90%, and in the case of high-quality devices it reaches 98%. They are characterized by a longer service life and increased reliability.

An example of a homemade lamp

Consider one of the most simple examples handmade ceiling lamp

For the manufacture we need:

5 l plastic bottle;
plastic spoons - their number depends on the dimensions of the bottle, which will become the frame;
quick-drying adhesive for plastic;
sharp knife;
cartridge with wire.

To begin with, a frame is prepared from a plastic bottle. Remove any labels from the item, rinse and dry thoroughly. After that, feel free to cut out the bottom. Cut off all the handles from the plastic spoons, but so that small pieces of 2 cm remain.

Glue the resulting scraps with “scoops” onto the base of the frame from a plastic bottle. To do this, we just need the remaining pieces of handles, which need to be poured abundantly with glue and pressed tightly to the surface (the convex part of the scoop should look out). Tape the container in a circle until the entire surface is hidden. Ideally, the spoons are placed in a checkerboard pattern, followed by a shift for a tight fit and no visible areas.

Cartridges with wiring can be removed from some old chandelier, then installed and fixed in a new product by pulling the bottle through the neck. A decorative bowl can be decorated with the same blanks using glue and placed on the neck.

To make sure that the product is working, at the final stage, screw the light bulb into the lamp and connect it to the power source. If successful, it remains to install the chandelier on the ceiling.

For more stylish design and shifts color solutions You can color plastic spoons. This will increase the originality and attractiveness of the product.

Style selection

In addition to the points listed in the first chapter of the article, when choosing a chandelier, you need to focus on a certain style. This is also true for those cases when you decide to make the product yourself. Comfort, coziness and how pleasant it will be to be in it depend on the interior created in the room.

The ceiling chandelier is the main element of the decor, therefore, with a competent approach, the perception of the environment will improve, with a careless one, it will completely deteriorate. As you know, “breaking is not building”, therefore, in order to spoil the interior, it is enough to choose the wrong style.

Decide in advance on the design of the future lamp. The most common styles for chandeliers are hi-tech, modern and provence.

High tech

It includes products made of glass and metal. Modern appliances fit perfectly into the design of the bedroom and living room. Externally, the chandelier may look chaotic (with an arbitrary arrangement of decor elements). Great option for people looking to modernize an apartment or a private house, but not wanting to make something too complicated. Any errors made in the manufacture of the chandelier may look like an original design decision.

Modern

In accordance with this style, appliances are made of glass and wood. The ceiling lamp is characterized by perfectly even and clear lines, has the correct geometry.

Provence

The most complex execution, which is suitable for people who understand the principles of hand-made. Various fabrics, colorful ribbons, beads, embroideries can be used to decorate the chandelier. The lamps are gentle, suitable for creating a romantic atmosphere. Provence style lighting fixture is suitable for decorating any living space.

Mounting materials

For ceiling mounting of the lamp, certain materials and tools will be required:

the lamp itself;
junction box;
screwdriver (curly);
switches;
as an alternative - dimmers (a rotary toggle switch that adjusts brightness, turn on / off the light bulb);
wires;
electrical tape;
indicator (tester);
pliers;
connecting blocks.

Ideally, electrical wiring should be routed using connector blocks. If such products are not available, then twist the bare ends of the wires with pliers and hide under a dense layer of electrical tape. The compounds can also be placed under polymer caps. Make sure the wires wrap tightly around each other.

When laying the cable, pay attention to the material from which it is made. It is advisable to twist aluminum with aluminum or copper with copper. When two wires come into contact different materials gradual oxidation will occur, leading to burnout and loss of contact.

Work sequence

Before installing the ceiling light, determine the phases of the wires. To do this, you need an indicator screwdriver or a special probe. If you attach the working surface to the phase core, the light bulb will start to glow. Otherwise, the wire belongs to the zero phase.

Next, you need to determine the phases on the wiring of the lighting fixture. Plug two wires into the outlet, but in no case touch the third one. If there are several bulbs on the chandelier, then about half of them will light up. Leave any wire in the outlet and replace the second with a third. The second half of the bulbs should light up. Thus, the wire that is constantly in the outlet (and when connected in turn with the other two turns on the light bulbs) is the zero phase.

Attach the lamp to the ceiling. For this, both a classic hook sticking out of the ceiling and a mounting rail (included with most modern devices) are used. If there is a hook from the old chandelier, it is advisable to dismantle it.

Connecting fixtures

If it is necessary to connect a floor lamp or chandelier with a two-wire cable, difficulties should not arise at all. Simply connect the ends of this cable to the two ends of the wiring. If the lamp consists of several parts and there are more wires, then it is correct to twist them in pairs, subsequently connecting them to the desired core electrical wiring in the apartment.

A three-core cable indicates the presence of two normal and one zero phases. Follow the scheme described above to find the zero phase. After that, connect the device to the house wiring.

Traditionally, the zero phase on the lamp has wires with blue insulation, the usual one is brown, black or red. If there are several blue wires, then they need to be connected in pairs, and then connected to the zero phase. Do the same with other colored parts.

Products with four cores are much less common. The latter is intended for grounding and is usually painted yellow-green. It should be screwed to the luminaire body with a conventional screw. Be sure to isolate all connections.

For the manufacture of ceiling lamps with your own hands, any materials can be used. The main thing is to choose the style and shape in advance and navigate the installation site. Also, before starting work, it is advisable to draw a sketch of the future product. Everything else is limited by your imagination.

Connecting homemade lighting fixtures is carried out in the same way as purchased ones. Using our instructions, you can easily connect ceiling chandeliers with two, three and even four cores. The main thing is not to forget about safety rules and ensure complete insulation of the wires, excluding a short circuit.

Indoor chandelier is not only lighting fixture. Without exaggeration, we can say that she is the main decoration of the room. Handmade items are considered especially valuable. This allows you to highlight the special taste of the owners of the home, as well as an outstanding and creative mind. Of course, this type of work is quite complex and requires increased concentration. But at the same time, when creating decorations for your home, you can find many interesting and extraordinary solutions in it!

This article presents some ideas for decorating a chandelier with your own hands, as well as instructions for them. Everything is written so simply and clearly that anyone can do what they have planned at home.

In order to make a chandelier, sometimes the most unusual materials are used. For example, everyone is already familiar with glass or wood, plastic, and so on. But sometimes, when you want something completely “unusual”, both wooden skewers and glass bottles out of wine, and cans, and all kinds of tree branches, and cardboard, and even straw. You need to choose depending on the idea of \u200b\u200bthe creator and on the wishes of the owners of the apartment. It is also necessary to take into account the general interior of the room where the finished product is supposed to be placed.

An interesting idea for a chandelier made of plastic spoons

Plastic disposable spoons are one of the simplest and most readily available materials for creating a chandelier for a room. Their advantages are low price, variety colors and will serve such material for quite a long time. To create such an extraordinary chandelier, you will need a minimum of investments, both physical and material.

Materials:

empty bottle from drinking water, with a volume of 5 liters;
plastic spoons (their number depends on the size of the bottle);
glue for plastic;
an old chandelier (or rather, a cartridge from it);
sharpened knife.

Process of creation:

First you need to prepare a plastic bottle for the next step. Remove the label in advance, cut off the bottom, dry well.
Then you need to get the plastic spoons out of the package and carefully cut off unnecessary handles with a knife, leaving about 2-3 centimeters above the level of the "scoop".
You need to glue the “scoops” blanks to the base of the bottle. On the left "tail" apply a large number of glue and press it to the surface (the convex side of the spoon out). It is necessary to cover the entire bottle in a circle until the entire perimeter is occupied by plastic "spoons". It is advisable to arrange them in a checkerboard pattern and slightly move them together. This will leave fewer "free spots".
You need to remove the cartridge from the old unnecessary chandelier, and then place it in an already glued and dried bottle and fix it on the frame.
A decorative bowl can also be made from plastic spoons: stick "scoops" around the neck of the eggplant.
Install and connect the chandelier, check its operation.

Note! The option of decorative painting or painting of spoons in absolutely any color is possible. Thus, your product will look even more beautiful and more original!

Chandelier made of plastic bottles in the form of leaves

Another unusual option a chandelier made in the form of leaves will serve in the interior. It is created from simple plastic bottles, the variety of colors of which allows you to work in the most unusual colors and embody the most daring ideas.

Process of creation:

Cut plastic bottles on blanks shaped like future leaves.
Each blank has to finally fix the shape of the sheet.
With a soldering iron with a thick tip and a one-sided bevel, you need to slightly fuse the sections of each leaf in order to give the future product the greatest effect.
In the same way, thanks to the soldering iron, you need to give the blanks a sheet structure. You need to act very carefully and accurately, because you can easily make a hole in the plastic. Such a leaf with outlined contours of veins and slightly fused edges will look complete.
With a hot needle at the "leg" of each leaf, you need to melt several holes in order to attach them.
Thanks to a thin wire, form branches and screw them to a steel wire frame.

It would also be a great idea to make a new chandelier in the form of a ceiling lamp for a floor lamp or a table lamp. Thus, it will be a great addition to the previous product!

Chandelier with paper butterflies

The most common version of the product is a chandelier with butterflies. And this is no accident. To begin with, this option looks luxurious and expensive, and secondly, its manufacture does not require special physical costs. Thus, even a child can participate in the creation of a chandelier.

Process of creation:

The basis is either an old chandelier or a similar frame. If this is not available, then you can take the simplest wooden or metal rim. If there is no such material, then, as an option, you can take a thick wire and make about 2-3 skeins, so that a circle forms.
Cut paper butterflies according to the pattern. You need to take a butterfly template and fit it to the desired size. The option also looks very unusual when butterflies of several sizes are located on the chandelier at once (again, depending on desire). Transfer the outlines to paper and carefully cut out, preferably with a sharpened clerical knife, or small non-rounded scissors. The material for the templates themselves is better to use dense, not very dirty and does not attract dust. For example, velvet paper is very bad for a product, because in the future you will need to vacuum the chandelier quite often.
Take a thread from a nylon or a transparent fishing line and attach butterflies to it. You can attach it in two ways: either pierce the bodies of butterflies, or stick them on silicone glue.
Next, we attach threads with butterflies to the base of the frame and decorate it.
You can also try interesting option if you make a wire ball! It should be based on a suspension from a chandelier and place several butterfly patterns on it using a glue gun.

fabric chandelier

This chandelier is also based on the frame. As in the previous version, either old metal frames or dense wire are suitable for its manufacture.

After you have pre-prepared the base, proceed to cutting out the fabric from which the lampshade will be made in the future. How long the finished product will be depends on your desire, but it should be borne in mind that the width of the fabric must be the same as the diameter of the frame! Once you have finished the pattern, you need to try on.

Another nuance is that the top of the fabric will need to be sewn directly on the frame, which means that it (the frame) must be solid. Otherwise, if it is possible to thread it directly into the fabric, then you should first fold the upper edge of the pattern and stitch it, and then iron it with an iron. Then we sew a seam on the side of the product.

In order for the lampshade not to lose its shape, due attention should be paid to the material. If the fabric is too light, "airy", then the bottom of the product should be weighted. To do this, you can use cardboard or fishing line.

A neatly sewn fringe, lace or braid will also look beautiful. But do not "overload" the product! The process of making a fabric chandelier is similar to making a lace chandelier. So you can safely experiment with materials that are located on the frame.

Plafond of threads and a balloon

Materials:

dense threads, such as woolen, cotton, or jute rope - at least 1 meter;
cartridge;
petrolatum;
PVA glue;
a brush to apply glue and petroleum jelly (it is desirable that the brush does not shed);
1 or 2 pieces of balloons (the first to work with it, and the second to check the finished product, if desired);

Process of creation:

Inflate the balloon to a certain size, secure. Remember that the finished work will exactly repeat the shape of the ball! With a marker, draw a couple of circles at the top and bottom, in order to determine the boundaries of winding threads.
Using a brush, smear the ball around the entire perimeter with petroleum jelly.
Pour PVA into a plastic container and thoroughly process the threads with it (It is not advisable to apply glue immediately to the entire length of the threads! Treat them as you wind them around the ball!).
Given the borders that you applied with a marker, wind the threads around the ball. Do not forget that depending on the density with which you wind, the future appearance of the product depends.
After winding, you need to leave the product for a day until it dries completely; After complete drying, you need to burst the ball and remove it through the holes.
Cut a place at the top and insert the cartridge.
In order to be completely sure that the product turned out to be strong, you can insert a ball into it and inflate it. Similarly, you can check the flexibility and reliability of the lampshade.

Alternatively, you can paint the structure with a spray can or acrylic paint, attach all kinds of decorative ornaments to it, such as butterflies, artificial flowers or beads. It's also a great idea to arrange a few balloons in the form of a bunch of grapes and fasten them together.

Wine bottle chandelier

This version of the chandelier is a little more complicated than the previous ones. Making a chandelier for this is quite difficult, the manufacturing process will require accuracy and care. However, you will love the result!

Materials:

a bottle of wine;
glass cutter;
sandpaper for sanding edges;
cartridge;
electric wire;
metallic or wooden frame, rim.

Process of creation:

First you need to prepare the bottle itself for further manipulations with it. The first step is to draw a straight line around the perimeter at the level you need. This is required in order to cut off the bottom of the bottle with a glass cutter;
In order not to cut yourself on the glass, you need to grind the sharp edges with sandpaper;
Pull the wire through the neck of the bottle and then connect the cartridge;
Attach the bottle to the frame.

You can also decorate the bottle with all kinds of decorative items, or leave it in its original form. In any case, it will look original and spectacular.

The number of products on the frame depends on your desire. You can either leave one bottle, or fix four or more bottles at once.

Chandelier idea from laserdiscs

This idea is great for those who have a large number of laser discs left in the house, and the hand does not rise to throw them away. It is immediately worth noting that the manufacturing options and the result can be very different. It all depends on your imagination and creativity!

Materials:

two round wooden planks of different thicknesses, and which are slightly larger in diameter than the disks;
racks made of metal or wood;
Fluorescent Lamp;
magnetic switch;
disks.

Process of creation:

Make a hole in a board with a greater thickness and install a starter with a switch in it.
Then connect it all to the lamp.
String disks on the lamp.
Install the racks around the discs and secure the top.

The finished product will delight its owners for a long time, and it does not require special care. It is not advisable to place this type of chandelier in the children's room so that the child cannot harm himself (only if the chandelier hangs out of reach).

Shabby chic chandelier

To create spectacular lighting in the room, you can also make a chandelier from fabric or beads. The result is a kind of chandelier or ceiling in the style of "shabby chic".

Materials:

a finished metal or wooden frame (or it can be made from an old hoop, garden basket, thick wire);
cartridge and lamp;
chains and threads for decoration;
all kinds of beads and beads.

Working on such a ceiling is not difficult, but it is a very painstaking task. Such chandeliers usually consist of two or three levels of rings, which are located one above the other. It all depends on the size of the selected bases. If you take rings of the same diameter, then the finished product will be made in the Art Nouveau style.

One of the important points is that before you start decorating the chandelier, you need to paint and wrap the frames with decorative materials!

The approximate consumption of beads is:

For the lower part of the lampshade - 16 mm beads, about 15-17 pieces per thread;
For the upper part of the lampshade - 12 mm beads, about 35 pieces per strand.

Naturally, when stringing beads on a thread, you can increase or decrease their number or the degree of thread tension. But it is still desirable to stock up on materials in excess of the norm.

The essence of the work is to hang threads with beads "waterfall" or "cascade" so that they flow down the structure.

In order to make the effect of "muting" the light, you can sheathe the frame with a thick fabric.

A handmade chandelier will definitely bring a fresh touch, originality and beauty to the interior. You will immediately notice how the room will sparkle with new colors, and your guests will sincerely admire your creativity, diligence and original taste!

90 photos of DIY chandelier ideas

The idea to make a lamp with my own hands came to mind when, after laying the linoleum in the house, there was a cardboard pipe left (on which the linoleum was wound).

To make a lamp with your own hands, it remains to buy just a little bit of 2 meters of black and red wire, 2 meters of adhesive-based LED strip, a 12V 1A power supply, spray paint in a can. The LED strip, of course, was a little expensive, but it is easier to work with. It was possible to use super-bright LEDs separately, but there is a lot of trouble with them in terms of desoldering between themselves and fastening inside the pipe.

Making a lamp with your own hands began with drawing preliminary sketches on paper. There was a desire that the lamp not only be curved in a plane, but also in space, and have a bizarre 3d wave shape.

After the sketch on paper satisfied my desires, I started making a lamp. Each pipe in the figure was measured and the pipes were cut to those dimensions. To get the necessary angles, templates were cut out of paper and fastened with tape on the pipe.

All tubes were laid out on the table, and adjustments were made to the waveform.

The cuts were made on a stationary circular saw. Thus, smooth cuts without burrs with a width of 2 mm are obtained.

Now you need to connect all the pipes into one. The main task is to make smooth bends, for this it does not hurt to apply a template (fiberboard sheet) on the table. Since the pipes are cardboard, they can be respectively connected using glue PVA, but I would recommend using adhesives that are stronger and harden faster (moment, superglue).

On the reverse side, wooden planks were screwed onto the screws so that the homemade lamp could be hung on the wall. And holes were drilled in each pipe for the output of wires from the LED strips.

The pipes were painted regular paint in a bottle. Red was used, since the wall on which the lamp should be located was white, I wanted to get some contrast.

The paint dries very quickly, so you can proceed with the installation of LEDs. The main thing to remember is what to cut led strip only available in designated areas. The tape must be marked in advance so that it is enough for all 12 pipes.

We solder red wires to the “+” contact, and black wires to the “-” contact, so as not to confuse the polarity later.

We place the LED strips inside the pipes and fix them with the adhesive side to the pipe wall, and we bring the wires out through the holes made in advance. It remains only to connect all the wires in parallel (connect red to red, and black to black) and connect to the power supply.