Herringbone from a greenish plastic bottle. Do-it-yourself Christmas tree: a master class with a photo on how to make a Christmas tree yourself

Do you think it is unrealistic to make a Christmas tree with your own hands from an ordinary plastic bottle? But no! And now we will prove it to you. By the way, such a Christmas tree looks pretty decent and very pretty! A plastic Christmas tree can be placed anywhere: even on a kitchen window, even on a bedside table near the TV, or even on a children's rack next to toys and books. So, to business?!

Materials and tools for .

To make a beautiful Christmas tree, we need:
one ordinary plastic bottle for 2 liters of green color;
landscape sheet of A4 format;
adhesive tape (adhesive tape);
scissors.

Agree, it is very pleasing that there is absolutely no glue! How to make a Christmas tree from a plastic bottle. Even a primary school student will cope with the task, and it will not be difficult for an adult to make a plastic Christmas tree!
1. Cut off the neck of the bottle so that you get a stand for a tree.

2. From the landscape sheet, you need to twist the trunk for the Christmas tree in the form of a cone. The diameter of the tube will correspond to the diameter of the bottle neck. Insert the handset into the stand.

3. Now cut these plates in the amount of nine pieces. Features of these blanks: 3 pcs. do rectangular shape measuring 8 cm by 7 cm; next 3 pcs. - 8 cm by 5.5 cm; the last 3 plates are 6 cm by 4 cm. It is not necessary to maintain the size in numbers, but the proportions of the blanks must be observed: large pieces, medium and small.

5. To make the branches lush, you need to twist them slightly: take the knife with the blunt side up and stretch it along the strip, firmly pressing the blade to the ribbons. It is not necessary to twist all the strips at once, it is difficult and inefficient. Take 4-5 ribbons.

6. Now you need to attach the needles to the paper trunk. To do this, we wrap it with plates, starting from the base. With the help of adhesive tape we fix each tier of needles. In the same way we move to the top.

New Year's crafts: tree from plastic bottles do-it-yourself - another extremely unusual and very beautiful craft from empty used plastic containers. In addition, you do not have to throw away the bottle, making an original masterpiece out of scrap. self made. To make such a Christmas tree, you need a minimum of time and cost. A master class on making a Christmas tree from plastic bottles will tell you in detail how to make an original New Year's craft from used materials, in this case PET containers.

Craft: DIY Christmas tree from plastic bottles

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

1. Plastic bottles - 3 pcs;
2. Scotch;
3. A sheet of thick paper, ideally whatman paper (A4);
4. Scissors;

So, cut the bottle as shown in the photo below. That is, it is necessary to cut off the bottom and neck so that a straight pipe from the bottle remains.

Next, you need to make blanks for the branches. In order for the Christmas tree to have a conical shape, the blanks must have different sizes. That is, you need to achieve the following:

Cut each plastic bottle lengthwise into 3 equal parts and only then adjust their sizes so that each subsequent tier is slightly smaller than the previous one. Then each blank must be "dissolved into needles." The neck of one of the bottles will serve as a stand for our future New Year's crafts.

The next step is to roll the paper into a tube. We insert it into the bottle neck and fix it with tape in a circle.

Now it remains to fix each tier of the tree with tape in a circle and a small New Year's craft: the tree is ready with your own hands!

You can decorate the top of our New Year tree with a homemade christmas toy or make the completion of the Christmas tree the way we did.

If you want to make a Christmas tree from PET bottles more fluffy, such as in the photo below, when making a Christmas tree, the needles need to be cut as thin as possible (more often).

Well, if you want to make a craft: Do-it-yourself Big Christmas Tree from plastic bottles, see the master class on making it.

Share your festive mood and new craft ideas, write your feedback, questions and wishes in the comments. We appreciate every action on your part. Happy crafting and have a wonderful New Year's mood!

See the rest of the workshops on manufacturing in various techniques.

1. Christmas tree made of plastic bottles

Make such a Christmas tree green plastic bottle, scotch, scissors(such that they can easily cut a plastic bottle, paper tube. The only thing that can be added to such a Christmas tree is that you can decorate it with beads by gluing them to the Christmas tree with glue. You can hang a ribbon of rain. You can do this craft with your kids. Next, we do everything as in the photo:

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

1. Plastic bottles - 3 pcs;
2. Scotch;
3. A sheet of thick paper, ideally whatman paper (A4);
4. Scissors;

So, cut the bottle as shown in the photo below. That is, it is necessary to cut off the bottom and neck so that a straight pipe from the bottle remains.

Cut each plastic bottle lengthwise into 3 equal parts and only then adjust their sizes so that each subsequent tier is slightly smaller than the previous one. Then each blank must be "dissolved into needles." The neck of one of the bottles will serve as a stand for our future New Year crafts

The next step is to roll the paper into a tube. We insert it into the bottle neck and fix it with tape in a circle.

You can decorate the top of our Christmas tree with a homemade Christmas tree toy or complete the Christmas tree the way we did.

If you want to make a Christmas tree from PET bottles more fluffy, such as in the photo below, when making a Christmas tree, the needles need to be cut as thin as possible (more often).

2. For Christmas trees from plastic bottles you will need green bottles of various sizes and a wooden stick, with a diameter slightly smaller than the neck. The length of the stick will determine the height of the tree and the number of bottles.

Probably done.)

4. Another very interesting option

For the manufacture we need:

• scissors
• green bottle
• cork stopper
• round cup of cottage cheese dessert
• candle
• glue.

Also find foam rubber. We cut off a piece of kitchen sponge for washing dishes.

First, cut the green bottle into squares or circles of different sizes. For the lower part of the Christmas tree, the width of the square should be at least 6-7 cm, the middle one should be about 5 cm, and 2-3 cm is enough for the crown.

Now with scissors we densely break through the edges of the stars. You can call family members for help. In fact, the work is painstaking and requires a lot of patience. Time edging the edges takes about 30 minutes. To make the spruce paws look more natural, we will bring the plastic to the flame of the candle. The tips of our coniferous twigs gracefully wrap down. Here is the finished result.

The turn has come to apply glue and foam rubber. Cut the sponge into small pieces (1x1 cm).

Now we grease the largest spruce paw with glue, apply a cube of foam rubber on top. We drip glue again and cover it with green plastic.

We continue to work until the details run out. Do not forget that we are “building a pyramid”, and therefore, with each subsequent gluing, we focus on the size of the plastic star.

It remains to arrange the trunk of a coniferous tree. Of course, cork will play its role. However, to make the craft resistant to tipping over, we will place the Christmas tree in a small yellow bucket. Cut it out of a round glass.

Lubricate the bottom of the bucket with glue, put the cork barrel in the center. Set aside the part for 2-3 minutes, let it dry completely.

We connect the crown with the trunk. It turned out a slender emerald plastic bottle tree. A true forest beauty.

Outcome

5. By the way, the Christmas tree looks quite creative with larger “branches”
We cut the bottle into 3 parts. Only cuts are made in a circle to the center, straight.

In the center, a puncture is made with an awl and the needles are bent up and down in order. In the lid of a cream or mineral water, a puncture is made into which a skewer of the desired length is inserted.

The parts are strung in descending order, a large bead is placed on top of the glue. The Christmas tree can be decorated with foam, rain, etc.

Glue the Christmas tree to the stand from the disk.
Christmas tree is ready

Today we bring to your attention the process of making a large holiday tree from simple green plastic bottles. This Christmas tree is collapsible, so it can be any number of tiers (only a longer “barrel” is required). You can add a tier every year and in a few years you will get a big fluffy beauty around which your children will dance.

To make a Christmas tree from plastic bottles, you need:

Green plastic bottles (it took 1.3 liter bottles about 30 pieces);

Steel part ("rod") of the desired length (here about 0.5 m, with an approximate diameter of 0.5 cm);

Single-core aluminum wire in insulation (section 2.5mm2);

Christmas tree stands;

Scissors, thermal gun;

Christmas tree from plastic bottles step by step:

Take the bottle and cut off the middle part from it, as in photo 2-3. Then cut this part bottles in a spiral with scissors, cut a strip about 2 centimeters wide (Pic 4).

Next, you need to bend one edge approximately 0.5 cm along the entire length of the strip, as in photo 5-6. This edge will help set the direction for spruce needles (needles), and will also serve as a limiter for cutting "needles". Cut a fringe strip about 0.1 cm wide (Pic 7-8).

Then proceed to the creation of spruce branches. Let's make a “top” for the Christmas tree, for which wrap a strip of plastic around the “rod” (about 8 cm long) and glue it with a thermal gun (apply glue to the “rod”, otherwise the workpiece from high temperature can be deformed) (photo 9). Next, twist a small piece of fringe and glue it inside the blank (photo 10). Then wrap the "rod" in a spiral with a strip of fringe (photo 11). When one strip ends, take another and continue gluing (photo 12-13).

After making the top - make the first tier of branches, which will consist of three short parts (a branch with an approximate length of about 7-8 cm). Make a wire frame as shown in photo 14, connect it to a plastic ring (photo 15-16).

Start wrapping the "twigs" by analogy with the top (photo 17). After creating all the branches, braid the “needles” and the main stem (photo 18-19). As a result, you should get two parts, as in photo 20.

Make the third part of the future Christmas tree, remote. At first it was made too high, so it was moved to the bottom of the tree and the part was made smaller. In total, four distances were used for this Christmas tree: Upper - approximately 0.5 cm; the second is about 0.6 cm; third - 7 cm; lower - 8 cm. Make "distances" by analogy with the manufacture of the crown, but do not close the upper hole (photo 21). The Christmas tree will look at this stage, as in photo 22.

Next, make a second tier of branches, which will be wider than the first and will already include four branches (approximately about 9 cm long), each of which will have two side branches. The length of the main branches turned out to be about 9 cm (photo 23 -24).

Wrap the frame, starting with the smallest branches, then the main ones, and ending with the trunk (photo 25-26). Under the influence of hot glue, the plastic heats up and takes on a fairly plastic shape, thanks to which it is very easy to set the direction of the needles for each branch at the junction of the branches (photo 27-29).

The central part of the stem before masking with needles looks like in photo 30, and after masking it looks like in photo 31. Next, you need to make a second remote part (photo 32).

This is followed by the manufacture of the third tier, the approximate length of the branches is about 10 cm (20 cm in diameter) (photo 33). Finally, make the lower tier (branches 15 cm long (30 cm in diameter)) and the lower distance (Pic 34).

It remains only to install everything on the stand! If desired, you can make any number of tiers, while each subsequent tier should be proportionally wider than the previous one - this way you can get a tall and elegant Christmas tree.

Christmas tree made of plastic bottles is ready!

According to the site: girlsschool.ru

The largest bottles should be at the bottom (2 and 1.5 liter, in the middle - liter, and at the top 0.5 and 0.3 liter bottles. If you have bottles of the same volume, then adjust the length of the “branches” yourself by cutting strips to desired length.

In the left bottom, make a hole, which is fixed on the lower end of the stick with a plastic bottle cork (for strength, you can hammer in a nail).

Put the last, smallest part on the upper end of the stick with the neck up and screw the green cork onto the neck, also securing it with a nail for strength.

A little patience, perseverance, diligence and the forest beauty is ready!

Such Christmas trees can be used as a New Year's decoration for your homes!

Method 2. To make such a Christmas tree, you need a minimum of time and cost. A master class on making a Christmas tree from plastic bottles will tell you in detail how to make such an original New Year's craft

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

1. Plastic bottles - 3 pcs;
2. Scotch;
3. A sheet of thick paper, ideally whatman paper (A4);
4. Scissors;

Method 3. And, finally, the last option for today is a Christmas tree made of plastic milk bottles (what decorative Christmas Trees just don’t make from ...). The design is completely collapsible, has the maximum resemblance to the original, does not require particularly complex technologies and specific work skills, there is no problem with bottles either, well, the holiday is on the nose ...

Materials and tools

The material for making a Christmas tree is a milk plastic bottle or part of it (Fig. 1). To make a homemade table Christmas tree, you need 5-20 milk / kefir plastic bottles with corrugation at the bottom. The number of bottles determines the number of branches and tiers. The more branches, the more fluffy the Christmas tree turns out, the more tiers, the higher it is.

In addition to bottles, you only need scissors and plastic rivet technology

plastic rivets

To implement the technology of plastic rivets, it is necessary to have a means for melting (installing) rivets and the rivet itself. You need to manage to melt the head of the rivet with a hot nail or a lighter. You can similarly do this with a well-heated soldering iron. In addition, you will need clamps and tweezers to install rivets in hard-to-reach places.

For plastic rivets, it is very important to choose the material. Fluttering for about a year, by trial and error, taking into account the requirements of strength and accessibility, I identified several sources for obtaining plastic rivets:

1. Empty refills from ballpoint pens. Fairly affordable material. They are good because they are colorless and the connection, with their help, turns out to be organically inscribed in a product made of plastic bottles. Such a rivet turns out to be neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross section and completely fills the drilled hole in the parts to be joined. By the way, the walls of the rods come in different thicknesses, for rivets it is better to use rods with thicker walls.

2. Sticks from Chupa Chups. Similar to option No. 1 only in color. The connection turns out to be more bulky, and the rivet head is melted with difficulty (either burns out, or becomes ugly, or unreliable).

3. The most ideal option, and very convenient (I give the world an offer) to use material from buckets with building mixtures of 3, 5, 10 liters. There are quite a lot of them left after repairs, and even one is enough for a long time.

From the walls of such a bucket, you need to cut a ring, and cut the ring along the generatrix (only this way) into strips 2 ... 4 mm wide, 4 to 15 cm long. quantity.

Getting a connection with such rivets is unpretentious. It is more convenient for this to pre-prepare rivets of the desired length, on the one hand, melting the head of the plastic rod. To connect two parts with plastic rivets, we overlap the parts, melt them with the same burner, forming a hole of the desired profile and size, insert a rivet there and, by melting, form a head from the opposite end of the rivet rod. Having practiced several times in reflow, the head is neat and tear-resistant.

Let's get started...

To implement the idea, the source material is needed in the form of a part of a milk plastic bottle (Fig. 1a), which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future Christmas tree are cut out of the ring with a central groove (Fig. 1c). From one whole plastic bottle, two or three rings are obtained. The more rings you prepare, the more fluffy and tall Christmas tree you can collect. I had 20 such rings, no less (10 full bottles).

Plastic rings with a groove in the middle must be cut into several equal parts (Fig. 2) along the generatrices of the bottle cylinder. As a result, we get convex rectangles. If cut into 2 parts, then long lower branches of the Christmas tree will be obtained from such long halves, if cut into 3 equal parts, then branches of the middle tiers will be obtained and middle length, and cutting into 4-5 parts, we get small blanks for the upper tiers of the desktop Christmas tree. It is not at all necessary to observe the special uniformity of the dimensions of the rectangles for one type of tiers.

Next, the rather tedious work of forming a branch begins. From each plastic convex rectangle (Fig. 3a), a wedge-shaped blank should be cut with scissors (Fig. 3b). The axis of symmetry of the wedge-shaped part should be along the corrugation groove. Immediately after cutting the workpiece, “needles” should be formed on it, making cuts along the side edges at about 45 degrees to the groove and radially at the end of the “branch”. (Fig. 3c). The needles are alternately bred from the plane of the workpiece also at 45 degrees to each other. The wiring of needles up and down relative to the plane of the branch provides fluffiness to the Christmas tree.

As a result of such painstaking work, several sets (Fig. 4) of branches of different sizes for a desktop homemade Christmas tree are obtained. Cutting branches and then needles is a rather lengthy task, but you can entrust this to your relatives as part of the collective creativity to decorate life under New Year. It should be noted that it is difficult to accurately determine the number of branches that form a particular tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

The place for fastening the branches is the trunk, which consists of several parts (logs). The upper parts of plastic bottles (Fig. 1b) were considered waste during the separation of the rings (Fig. 1c), but now they are also used in spruce construction to create a trunk. The base of the trunk and the lower log is the full neck part of a plastic bottle (Fig. 5a). The upper logs are assembled from blanks obtained by cutting off the threaded part of a milk bottle with a flange, as well as removing a plastic segment along the generatrices (Fig. 5b, 5c). The segments must be rolled up with a tube and fixed on both sides of the generatrix with plastic rivets. Similarly, it is necessary to create several logs for attaching tiers of branches. In my case, these are 3 logs, but there may be more or less of them. For a miniature Christmas tree, 3-4 tiers of branches on just one log are enough.

Naturally, the diameter of the trunk should taper towards the top of the table tree and the diameter of the top log should be smaller than the bottom one. The larger the cut of the segment, the more top log is obtained from the tapered top of the plastic bottle. For the top, you need a half segment, and for the middle part, about two-thirds of the whole neck (Fig. 5b). The diameter of the bottom hole of the top log should be approximately 1 mm larger than the top hole of the bottom log forming the trunk.

It's time to attach the branches to the "logs". On each log, you will need to place 2-3 tiers of branches. A small number of tiers does not allow you to effectively cover the rivet heads with branches, and a large number of spoils the aesthetic appearance of the Christmas tree. In each tier of this design, you can install from 4 to 10 branches. Fastening is carried out with the help of plastic rivets, since quite a lot of plastic rivets will be required, it is better to prepare them for future use. The easiest way is to install branches in tiers on the lower logs (Fig. 6), since the neck in a plastic bottle is wide enough and it is convenient to hold a plastic rivet with inside finger.

If you put the branches close to the circumference of the tier, then one rivet is enough to fasten the branch to the trunk (Fig. 6-8). For lovers of greater reliability, two rivets can be installed side by side. The tiers of branches must be formed like the flooring of the roof of a house - from the bottom up, then the branches of the upper tier will cover the rivets of the lower one and the heads of the rivets will be completely invisible.

In my case, in the lower (Fig. 6) and middle (Fig. 7) logs of the trunk, there are 2 tiers of branches, and in the upper - 3 (Fig. 8). In total - 5 tiers of branches. It is quite enough to acquire an amazing similarity with a real Christmas tree. The installation of plastic rivets on the upper tier, due to its small diameter, should be done using tweezers or a medical clip.

After fixing all the tiers on all the logs, you can proceed to the final assembly. But first it is desirable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the barrel (Fig. 5), that is, turning the plastic into a cone. But you can do this in a different way, for example, in the form of an asterisk or a ball (I like the cone more). The top of the tree is attached to the upper element of the trunk also with the help of a rivet that is installed from the inside and melted from the outside. The upper part of the trunk, together with the top, already has a miniature table Christmas tree in itself (Fig. 9). It can be installed on the monitor and enhance the feeling of the holiday...

A live Christmas tree grows from the bottom up, in the same order we collect logs with tiers of branches by adding “logs” (Fig. 10) to an existing Christmas tree. Between themselves, it is better to connect the elements of the trunk in a place covered with a branch, at three points along the circumference of the trunk. In this case, the trunk acquires rigidity and will not break if the Christmas tree accidentally falls to the floor from the table, then the Christmas tree is desktop ...

And if you insert a light-dynamic part (for example, a garland) inside the Christmas tree, then on New Year's Eve it will amaze those around you with its charm:

Here is such a master class. Of course, a little complicated, but what a beauty it turns out!