Loop turned gost. Hinges for windows and doors

HINGES FOR WINDOW AND DOOR UNITS

Specifications

INTERSTATE SCIENTIFIC AND TECHNICAL COMMISSION FOR STANDARDIZATION, TECHNICAL REGULATION AND CERTIFICATION IN CONSTRUCTION (MNTKS)

Foreword

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 * “Interstate standardization system. Basic provisions” and MSN 1.01-01-96 “System of interstate normative documents in construction. Basic Provisions»

About the standard

1 DEVELOPED by the institution "Certification Center for Window and Door Equipment" with the participation of the Federal State Unitary Enterprise "Central Design and Technological Bureau" of the Gosstroy of Russia, the company " Fiskars ", Finland and the company " Dr. Hahn ”, Germany, ZAO TBM

2 INTRODUCED by the Technical Committee for Standardization TK465 "Construction"

3 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTCS) (Minutes No. 28 of October 13, 2005)

4 By order of the Federal Agency for Technical Regulation and Metrology dated April 24, 2006 No. 76-st, the interstate standard GOST 5088-2005 was put into effect as the national standard of the Russian Federation from January 1, 2007.

INTERSTATE STANDARD

the dateintroductions - 2007-01-01

1 area of ​​use

This standard applies to metal hinges (hereinafter referred to as hinges) used in window and door blocks made of various materials.

The standard does not apply to hinges installed on window and door blocks for special purposes, in terms of additional requirements for fire safety and burglary resistance.

2 Normative references

This standard uses references to the following standards:

The shape of the cards for mortise and overhead loops is set in the working drawings for a specific type of loop.

5.2.2 The ovality of the axes (semi-axes) in the places of movable connections with the loop cards should be no more than 0.1, and the tubes of the loop cards - 0.3 mm.

5.2.3 The gap between the axle or semi-axle and the loop tube in the places of movable joints must be at least 0.1 and not more than 0.5 mm.

5.2.4 Deviation from the perpendicularity of the bearing surfaces of the axes of the hinges of types PN1 - PN4 and PV1 relative to the axes of rotation should be no more than 0.25 mm.

5.2.5 The gap between the tube and the plane of the loop map is not more than 0.5 mm.

5.2.6 Longitudinal and transverse play in the hinges of hinges of types PN8 and PN9 must be no more than 0.3 mm.

5.2.7 The gap between the plane of the loop card and its bent end (tube) should be no more than 0.5 mm with a thickness of the loop card up to 2.2 mm and 1.0 mm - with a thickness of more than 2.2 mm.

5.3 Design requirements

5.3.1 The design of the hinges must be strong and reliable and ensure the possibility of their repair and replacement.

5.3.2 In the designs of overhead hinges, it is recommended to provide adjusting screws for their adjustment in different planes.

At the same time, the design of steel adjustable hinges must ensure the adjustment of the hinge ± 2 mm in the horizontal and vertical planes; for the construction of loops from aluminum profile- ± 5 mm.

The adjusting screws must be located in places accessible for adjustment.

5.3.3 The design of the hinges must ensure reliable fastening to the doors (cloths) and boxes. The location and dimensions of the holes for installing hinges are indicated in the working drawings for specific types of window (door) blocks.

An example of calculating and choosing the type of screw-in hinges for a window block made of wood is given in.

5.3.4 Rotation of overhead cards, mortise hinges and screw-in hinge rods must be without jamming around the axes and semi-axes.

To ensure rotation without sticking of the cards around the axes and semi-axes of the hinges, it is recommended to use bearings.

5.3.5 The fastening of the half-loops to the sash (leaf) and the frame is carried out through structural holes, fixing plates or by welding.

5.3.6 Additional anti-removable elements ( ) can be provided in the hinge map to improve the safety and security properties of door blocks.

5.3.7 Overhead hinges intended for installation on the glass elements of door blocks must be installed through gaskets that exclude the possibility of contact between the metal parts of the hinges and glass.

5.3.8 The metric thread on the rods of the screw-in hinges must be complete, without dents and thread breaks, and meet the requirements GOST 24705.

5.3.9 The design of hinges of types PN8 and PN9 should provide for the possibility of adjusting the closing force of the door leaf, while the opening force of the door block should be at least 2 and not more than 4 kgf at a distance of 700 mm from the hinge axis.

5.3.10 The head of the axle or semi-axle of the hinges shall have a spherical or truncated cone shape.

The chamfer at the end of the axis of the hinges of types PN1 - PN4, PN6 - PN9 and PVv1 - PVv3 should be (2 - 3) × 30 °.

5.3.11 Hinges of types PN7, PV2 - PV4 are equipped with cotter pins 2× 16 by GOST 397or quick-release thrust washers 5 - 080 on GOST 11648.

5.3.12 Loops of types PN1 - PN4, PN6 and PV1 are made right and left (right loops are shown on , , , , ).

5.3.13 Connections of hinge cards with axes and semi-axes in overhead hinges of type PN7 and mortise hinge of type PV1 must be one-piece.

5.3.14 The connection of the hinge parts is allowed to be carried out by resistance welding according toGOST 15878. Welds must be clean and free from open areas and burns. Another type of connection of the hinge parts is allowed, which ensures its strength.

5.3.15 Requirements for hinge designs intended for installation on window blocks with tilt-and-turn, turn and tilt devices, - according toGOST 30777.

5.4 Reliability and load resistance requirements

5.4.1 When tested for failure-free operation, the hinges must withstand the number of “opening-closing” cycles in accordance with Table 2.

table 2

5.4.2 The connection of rods with bushings or brackets in screw-in loops must withstand a pull-off force of at least 800 N.

5.4.3 Resistance to static and dynamic loads of hinges is determined in finished window (door) blocks, taking into account their design and material, as well as the fasteners used.

5.5 Requirements for materials and components

5.5.1 For the manufacture of hinges, the following materials should be used: steel, brass, plastic and a special aluminum profile according to the current regulatory documentation.

Gaskets used in hinges for door blocks made of tempered glass, must be made of weather- and frost-resistant elastic polymeric materials.

5.5.2 Materials and components used for the manufacture of hinges must be resistant to climatic influences.

Polymeric and synthetic materials must have a sanitary and epidemiological conclusion drawn up in the prescribed manner.

5.5.3 Details of hinges made of non-corrosion-resistant materials must have a protective, protective and decorative anti-corrosion coating. Requirements for coatings and corrosion resistance - according toGOST 538.

5.5.4 Hinges to sashes (cloths) and boxes are fixed with screws, screws, self-tapping screws (screws) with anti-corrosion coating or welding. Hinges made of aluminum profiles are fastened with screws screwed into special embedded elements.

5.5.5 Welded joints of loops must be strong and meet the following requirements (visually controlled):

The weld metal and the boundary zone must not have cracks. Seam craters at the places where welding stops (ends) must be overcooked (welded);

The surface of the seams should be smooth or uniformly scaly without sharp transitions to the base metal;

The seams must be tight along the entire length and not have burns, constrictions, welds, lack of penetration, slag inclusions, etc.

The tensile strength of the metal of the welded joint of the loops must not be lower than the requirements for the base metal.

5.6 Completeness

5.6.1 Hinges must be supplied complete in accordance withGOST 538. The delivery set should include a complete set of elements necessary for the installation and operation of hinges on a window or door block.

A label in accordance with GOST 2.601 must be attached to each batch of loops, as well as when selling loops through a retail distribution network. One copy of the installation instructions and maintenance should be included in every box with hinges.

5.6.2 Upon agreement with the customer, it is allowed to supply hinges without fasteners.

5.7 Labeling and packaging

5.7.1 Marking the hinges - according toGOST 538.

The letters P or L are applied to the loops - for right and left loops, on universal hinges the designation is not applied.

5.7.2 Requirements for packing loops - according toGOST 538.

Additional packaging requirements, if necessary, may be specified in the supply contract.

6 Acceptance rules

6.1 Acceptance of loops is carried out in accordance with the requirements of this standard andGOST 538.

Loops are accepted in batches. When accepting loops at the manufacturing plant, a batch is considered to be the number of loops of the same name, manufactured within one shift and issued with one quality document. A batch is also considered the number of loops of one design, made according to one order.

6.2 The quality of the loops for compliance with the requirements of this standard is confirmed by:

Incoming control of materials and components;

Operational production control;

Acceptance control of finished loops;

Periodic and certification tests;

type tests;

Qualification tests.

6.3 The procedure for conducting incoming and operational production control at workplaces is established in the technological documentation for hinges.

6.4 Acceptance quality control finished products and periodic tests are carried out in accordance with table 3. The control plan and the procedure for conducting acceptance control - according toGOST 538.

Table 3

Dimensions in mm

Figure B.8 - An example of an overhead hinge type PN5

Dimensions in mm

Figure B.12 - An example of an overhead hinge type PN8

Figure B.13 - An example of an overhead loop of size PN-115

*For door blocks with a leaf thickness of 52 mm.

Figure B.14 - An example of an overhead hinge type PN9

Dimensions in mm

Figure B.16 - An example of a mortise hinge type PV2

*For window units with triple glazing; pins - 4 pcs; the length of the pins is specified when ordering.

Figure B.17 - An example of a PVZ type mortise hinge 30

22,5

Mon4–75

27,5

2,0 - 2,5

PN4-90

Figure B.18 - An example of a mortise hinge PV4

Figure B.19 - An example of a mortise hinge, size PV4-10 0

Figure B.20 - An example of a screw-in hinge type PVv1

Figure B.21 - An example of a screw-in hinge type PVv3

Figure B.22 - An example of a screw-in hinge type PVv3

Figure B.23 - An example of an aluminum profile hinge for window and door blocks made of aluminum alloys and PVC profiles with a maximum weight of 80 kg

Figure B.24 - An example of an aluminum profile overlay hinge for door blocks made of aluminum alloys and PVC profiles

Figure B.25 - An example of an aluminum profile overlay hinge for door blocks made of aluminum alloys and PVC profiles

Figure B.26 - An example of a set of ball axleless hinges for metal doors

Figure B.27 - An example of a combined hinge for a door unit with a tempered glass leaf

Annex B
(reference)
An example of calculating and choosing the type of screw-in hinges for a window block made of wood

Figure B.1 - Scheme for determining the loads acting on the screw
hinges in a wooden window block, with flat sash loading

The limit specified loads acting on the loops are calculated by the formulas:

; (1)

(2)

where R pr- limiting external concentrated load acting in the plane of the sash;

R g - horizontal (pulling out) force acting on the loop;

R in - vertical load (shear) acting on the hinge rod;

H- sash height;

AT- sash width;

a - the distance that determines the location of the loop in the block;

G- mass of the sash.

The design loads for a particular loop are calculated using the formulas:

The limiting value of the stress that occurs in the wood when it is crushed (tensile strength) across the fibers;

The limiting value of stress (tensile strength) that occurs in wood when it is crushed along the fibers.

The condition for selecting a loop is: .

When calculating, it is necessary to take into account not only the mass and dimensions a specific sash (leaf), but also the characteristics of the materials of the window (door) block.

Keywords : hinges, overhead hinges, mortise hinges, screw-in hinges, window blocks, door blocks.

I like

GOST 5088-2005

INTERSTATE STANDARD HINGES FOR WINDOW AND DOOR UNITS SPECIFICATIONS

Hinges for windows and doors. Specifications

Group Zh34

Foreword

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 "Interstate standardization system. Basic provisions" and MSN 1.01-01-96 "System of interstate regulatory documents in construction. Basic provisions".

About the standard

1. Developed by the institution "Certification Center for Window and Door Equipment" with the participation of the Federal State Unitary Enterprise "Central Design and Technology Bureau" of the Gosstroy of Russia, the company "Fiskars", Finland, and the company "Dr. Hahn", Germany, CJSC "TBM".

2. Introduced by the Technical Committee for Standardization TC 465 "Construction".

3. Adopted by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (MNTKS) (Minutes No. 28 of October 13, 2005).

4. By order of the Federal Agency for Technical Regulation and Metrology dated April 24, 2006 N 76-st, the interstate standard GOST 5088-2005 was put into effect as the national standard of the Russian Federation from January 1, 2007.

5. Instead of GOST 5088-94.

Application area

This standard applies to metal hinges (hereinafter referred to as hinges) used in window and door blocks made of various materials.

The standard does not apply to hinges installed on window and door blocks for special purposes, in terms of additional requirements for fire safety and burglary resistance.

Normative references

GOST 2.601-95. Unified system of design documentation. Operating documents

GOST 9.308-85. Unified system of protection against corrosion and aging. Metallic and non-metallic inorganic coatings. Accelerated Corrosion Test Methods

GOST 9.401-91. Unified system of protection against corrosion and aging. Paint coatings. General requirements and methods of accelerated tests for resistance to climatic factors

GOST 397-79. Pins. Specifications

Table 3

6.5. Periodic testing of products is carried out once every two years. Tests are carried out on samples that have passed acceptance control.

6.7. Type testing of products is carried out after changes are made to the design, materials or manufacturing technology to assess the effectiveness and feasibility of making changes.

The scope of type tests is determined by the nature of the changes made.

Type tests are carried out on products that have passed acceptance control.

6.8. Qualification tests of products are carried out for all indicators when putting products into production.

6.9. Certification and periodic tests are carried out in testing centers (laboratories) accredited for the right to test these products.

6.10. Each batch of products must be accompanied by a quality document.

6.11. Acceptance of products by the consumer does not release the manufacturer from liability in case of detection of hidden defects that led to a violation performance characteristics products during warranty period services.

Control methods

7.1. Compliance of materials and components with the requirements of regulatory documents is established by comparing indicators accompanying documents with the requirements of ND for materials and components.

7.2. Loop sizes and limit deviations are determined by a universal tool, and software methods for controlling the manufacturing process of manufacturers are also used.

7.3. The appearance of products, welds, completeness, the presence of markings, packaging are visually checked for compliance with the requirements of this standard, design documentation and standard sample.

7.4. The quality of coatings is checked according to GOST 538; adhesion - GOST 15140; corrosion resistance of coatings - GOST 9.308, GOST 9.401.

7.5. The operation of the moving parts of the loop is checked manually, repeating the cycle of the loop at least five times.

7.6. Tests of products for reliability, resistance to static and dynamic loads are carried out on special equipment(stands) according to agreed and approved programs and methods.

After testing, the loops must remain operational.

Transportation and storage

8.1. Loops are transported by all means of transport in accordance with the rules for the carriage of goods in force for this type of transport.

8.2. During storage and transportation, the hinges protect against the effects of atmospheric precipitation and protect against mechanical damage.

8.3. Storage conditions for products - according to group 2 GOST 15150.

Installation and operating instructions

9.1. The choice of hinge design, the required number for installation on a window (door) unit and installation should be carried out in accordance with the recommendations and design programs of manufacturers.

9.2. Mounting of the hinges should be carried out in accordance with the mounting instructions included in the scope of supply.
Installation of products should be carried out using special templates.

9.3. Lubrication and adjustment of the hinges during operation is carried out in accordance with the instruction manual included in the delivery.

manufacturer's warranty

10.1. The manufacturer guarantees the compliance of the hinges with the requirements of this standard, provided that the consumer complies with the rules for transportation, storage, installation, operation, as well as the scope established in the regulatory and project documentation.

HINGES FOR WINDOW
AND DOOR BLOCKS

Specifications

INTERSTATE SCIENTIFIC AND TECHNICAL COMMISSION
ON STANDARDIZATION, TECHNICAL REGULATION
AND CERTIFICATIONS IN CONSTRUCTION
(MNTKS)

Foreword

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established GOST 1.0-92“Interstate system of standardization. Basic Provisions” and MSN 1.01-01-96“The system of interstate regulatory documents in construction. Basic Provisions»

About the standard

1 DEVELOPED by the institution "Certification Center for Window and Door Equipment" with the participation of the Federal State Unitary Enterprise "Central Design and Technology Bureau" of the Gosstroy of Russia, the company " Fiskars ”, Finland and the firm “Dr. Hahn, Germany, ZAO TBM

2 INTRODUCED by the Technical Committee for StandardizationTK 465 "Construction"

3 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (MNTKS) (Minutes No. 28 dated October 13, 2005)

4 Order of the Federal Agency for Technical Regulation and Metrology dated April 24, 2006 No. 76-st interstate standard GOST 5088-2005 was put into effect as the national standard of the Russian Federation on January 1, 2007.

6 REVISION. April 2007

Information on the entry into force (termination) of this standard is published in the index "National Standards".

Information about changes to this standard is published in the index "National standards", and the text of the changes - in information signs "National standards". In case of revision or cancellation of this standard, the relevant information will be published in the information index "National Standards"

INTERSTATE STANDARD

HINGES FOR WINDOW AND DOOR UNITS

Specifications

Hinges for windows and doors.
Specifications

Introduction date - 200 7- 01 - 01

1 area of ​​use

This standard applies to metal hinges (hereinafter referred to as hinges) used in window and door blocks made of various materials.

The standard does not apply to hinges installed on window and door blocks for special purposes, in terms of additional requirements for fire safety and burglary resistance.

2 Normative references

This standard uses references to the following standards:

4.3 Symbols for types of loops and the recommended scope of their application are given in the table. Examples of hinges and their components are given in the appendix.

Table 1

Set the following loop symbol structure:

Symbol examplehinges of the consignment note type PN1, height 110 mm, right:

PN1-110-P GOST 5088-2005

The same, mortise type PV4, height 90 mm, universal, version 1:

PV4-90-1 GOST 5088-2005

It is allowed to include alphabetic and numeric designations in the symbol of the loops in accordance with the design documentation (hereinafter - CD) for the loops.

For export-import deliveries, it is allowed to use the designations of loops accepted from the supplier and specified in the agreement (contract).

5 Technical requirements

5.1 General

Limit deviations of matched and non-matched sizes - according to GOST 538.

The shape of the cards for mortise and overhead loops is set inworking drawings for a specific type of hinge.

5.2.2 The ovality of the axes (semi-axes) in the places of movable connections with the loop cards should be no more than 0.1, and the tubes of the loop cards - 0.3 mm.

5.2.3 The gap between the axle or semi-axle and the loop tube in the places of movable joints must be at least 0.1 and not more than 0.5 mm.

5.2.4 Deviation from perpendicularity of the supporting surfaces of the axes of the loops of types PN1 - PN4 and PV1 relative to the axes of rotation should be no more than 0.25 mm.

5.2.5 The gap between the tube and the plane of the loop map is not more than 0.5 mm.

5.2.6 Longitudinal and transverse play in the hinges of hinges of types PN8 and PN9 must be no more than 0.3 mm.

5.2.7 The gap between the plane of the loop card and its bent end (tube) should be no more than 0.5 mm with a thickness of the loop card up to 2.2 mm and1.0 mm - with a thickness of more than 2.2 mm.

5.3 Design requirements

5.3.1 The design of the hinges must be strong and reliable and ensure the possibility of their repair and replacement.

5.3.2 In the designs of overhead hinges, it is recommended to provide adjusting screws for their adjustment in different planes.

At the same time, the design of steel adjustable hinges must provide adjustment of the hinge ± 2 mm in the horizontal and vertical planes; for the construction of aluminum profile hinges -±5 mm.

The adjusting screws must be located in places accessible for adjustment.

5.3.3 The design of the hinges must ensure reliable fastening to the doors (cloths) and boxes. The location and dimensions of the holes for installing hinges are indicated in the working drawings for specific types of window (door) blocks.

An example of calculating and choosing the type of screw-in hinges for a window block made of wood is given in the appendix.

To ensure rotation without sticking of the cards around the axes and semi-axes of the loops, it is recommended to use bearings.

5.3.5 The fastening of the half-loops to the sash (leaf) and the frame is carried out through structural holes, fixing plates or by welding.

5.3.6 Additional anti-removable elements can be provided in the hinge map to improve the safety and security properties of door blocks (application figure).

5.3.7 Overhead hinges intended for installation on the glass elements of door blocks must be installed through gaskets that exclude the possibility of contact between the metal parts of the hinges and glass.

5.3.8 The metric thread on the rods of the screw-in hinges must be complete, without dents and thread breaks, and meet the requirements GOST 24705.

5.3.9 The design of hinges of types PN8 and PN9 should provide for the possibility of adjusting the closing force of the door leaf, while the opening force of the door block should be at least 2 and not more than 4 kgf at a distance of 700 mm from the hinge axis.

5.3.10 The head of the axle or semi-axle of the hinges shall have a spherical or truncated cone shape.

Chamfer on the end of the axis of the hinges of types PN1 - PN4, PN6 - PN9 and PVv1 - PVv3 should be (2 - 3)´ 30°.

5.3. 11 Hinges of types PN7, PV2 - PV4 are completed with cotter pins 2´ 16th to GOST 397 or quick release thrust washers 5-080 according to GOST 11648.

5.3.12 Hinges of types PN1 - PN4, PN6 and PV1 are made right and left (right hinges are shown in the figures , , , , appendices).

5.3. 13 Connections of hinge cards with axes and semi-axes in overhead hinges of the PN7 type and the mortise hinge of the PV1 type must be one-piece.

5.3.14 The connection of the hinge parts is allowed to be carried out by resistance welding according to GOST 15878. Welds must be clean and free from open areas and burns. Another type of connection of the hinge parts is allowed, which ensures its strength.

5.3.15 Requirements for hinge structures intended for installation on window blocks with tilt-and-turn, turn and tilt devices - according to GOST 30777.

5.4 Requirements for reliability and load resistance

5.4.1 When testing for failure-free operation, the hinges must withstand the number of “opening-closing” cycles in accordance with the table.

table 2

5.4.2 The connection of rods with bushings or brackets in screw-in loops must withstand a pull-off force of at least 800 N.

5.4.3 Resistance to static and dynamic loads of hinges is determined in finished window (door) blocks, taking into account their design and material, as well as the fasteners used.

5.5 Requirements for materials and components

5.5.1 For the manufacture of hinges, the following materials should be used: steel, brass, plastic and a special aluminum profile according to the current regulatory documentation.

Gaskets used in hinges for tempered glass door blocks must be made of weather-resistant elastic polymer materials.

5.5.2 Materials and components used for the manufacture of hinges must be resistant to climatic influences.

Polymeric and synthetic materials must have a sanitary and epidemiological conclusion drawn up in the prescribed manner.

The weld metal and the boundary zone must not have cracks. seam cratersin places of stopping (end) of welding must be digested (brewed);

The surface of the seams should be smooth or evenly scaly without sharp transitions to the base metal;

The seams must be tight along the entire length and not have burns, constrictions, welds, lack of penetration, slag inclusions, etc.

The tensile strength of the metal of the welded joint of the loops must not be lower than the requirements for the base metal.

5.6 Completeness

5.6.1 Hinges must be supplied complete in accordance with GOST 538. The delivery set should include a complete set of elements necessary for the installation and operation of hinges on a window or door block.

Each batch of loops, as well as the sale of loops through a retail network, must be accompanied by a label according to GOST 2.601. One copy of the installation and maintenance instructions must be included in each box. to with loops.

5.6.2 Upon agreement with the customer, it is allowed to supply hinges without fasteners.

5.7 Marking and packaging

5.7.1 Marking the hinges - according to GOST 538.

The letters P or L are applied to the loops - for right and left loops, the designation is not applied to universal loops.

5.7.2 Requirements for packing loops - according to GOST 538.

Additional packaging requirements, if necessary, may be specified in the supply contract.

6 Acceptance rules

6.1 Acceptance of loops is carried out in accordance with the requirements of this standard and GOST 538.

Loops are accepted in batches. When accepting loops at the manufacturing plant, a batch is considered to be the number of loops of the same name, made within one shift and issued with one quality document. A batch is also considered the number of loops of one design, made according to one order.

6.2 The quality of the loops for compliance with the requirements of this standard is confirmed by:

Incoming control of materials and components;

Operational production control;

Acceptance control of finished loops;

Periodic and certification tests;

type tests;

Qualification tests.

6.3 The procedure for conducting incoming and operational production control at workplaces is established in the technological documentation for hinges.

6.4 Acceptance quality control of finished products and periodic tests are carried out in accordance with the table. Control plan and order acceptance control- on GOST 538.

Table 3

6.5 Periodic testing of products is carried out once every two years. Tests are carried out on samples that have passed acceptance control.

6.6 Certification tests of products are recommended to be carried out in the scope of periodic tests.

6.7 Type tests of products are carried out after changes are made to the design, materials or manufacturing technology to assess the effectiveness and feasibility of making changes.

The scope of type tests is determined by the nature of the changes made.

Type tests are carried out on products that have passed acceptance control.

6.8 Qualification tests of products are carried out for all indicators when putting products into production.

6.9 Certification and periodic tests are carried out in test centers (laboratories) accredited for the right to test these products.

6.10 Each batch of products must be accompanied by a quality document.

6. 11 Acceptance of products by the consumer does not release the manufacturer from liability in case of detection of hidden defects that led to a violation of the performance characteristics of products during the warranty period.

7 Control methods

7.1 Compliance of materials and components with the requirements of regulatory documents is established by comparing the indicators of accompanying documents with the requirements of RD for materials and components.

7.2 Loop sizes and limit deviations are determined with a universal tool, and software methods for controlling the manufacturing process of manufacturers are also used.

7.3 The appearance of products, welds, completeness, presence of markings, packaging are visually checked for compliance with the requirements of this standard, design documentation and standard sample.

7.4 The quality of coatings is checked by GOST 538; adhesion - GOST 15140; corrosion resistance of coatings - GOST 9.308 , GOST 9.401.

7.5 The operation of the moving parts of the hinge is checked manually, repeating the cycle of the hinge at least five times.

7.6 Tests of products for failure-free operation, resistance to static and dynamic loads are carried out on special equipment (benches) according to agreed and approved programs and methods.

After testing, the loops must remain operational.

8 Transport and storage

8.1 Loops are transported by all means of transport in accordance with the rules for the carriage of goods in force for this type of transport.

8.2 During storage and transportation, the hinges protect against the effects of atmospheric precipitation and protect against mechanical damage.

8.3 Storage conditions for products - group 2 GOST 15150.

9 Installation and operating instructions

9.1 The choice of hinge design, the required number for installation on a window (door) unit and installation should be carried out in accordance with the recommendations and design programs of manufacturers.

9.2 Mounting of the hinges should be carried out in accordance with the mounting instructions included in the delivery.

Installation of products should be carried out using special templates.

9.3 Lubrication and adjustment of the hinges during operation is carried out in accordance with the operating instructions included in the delivery.

10 Manufacturer's warranties

10.1 The manufacturer guarantees the compliance of the hinges with the requirements of this standard, provided that the consumer complies with the rules for transportation, storage, installation, operation, as well as the scope established in the regulatory and project documentation.

10.2 Guaranteed period of operation of the hinges is at least 24 months from the date of commissioning of window (door) units or from the date of sale of the hinges through the distribution network.

Annex A

Basic hinge details

1 - map with a tube; 2 - axis; 3 - axle shaft

Figure A.1 - Main details of overhead and mortise hinges

1 - rod; 2 - sleeve; 3 - axis; 4 - brace

Figure A.2 - Main details of screw-in hinges

Annex B

Examples of hinges and their accessories

Standard sizes PN1-70, PN1-85

Standard sizes PN1-110, PN1-130, PN1-150

In millimeters

Figure B.1 - An example of an overhead hinge type PN1

Figure B. 2 - An example of an overhead hinge, size PN1-110

Figure B.3 - An example of an anti-removable patch loop of size PN1- 110

Sizes PN2-70, PN2-85 Sizes PN2- 110, PN2-130, PN2-150

Dimensions in mm

Figure B.4 - An example of an overhead hinge type PN2

Standard size PN3-85

Standard sizes PN3-110, PN3-130, PN3-150

Dimensions in mm

Figure B.5 - Examples of overhead loop type PN3

Figure B. 6 - An example of an overhead hinge, size PN3-130

Figure B. 7 - Examples of overhead loop type PN4

Dimensions in mm

Figure B.8 - An example of an overhead hinge type PN5

Standard size PN6-80

Standard size PN6- 110

Dimensions in mm

Figure B. 9 - An example of an overhead hinge type PN6

Version 1

Execution 2

Figure B. 10 - An example of an overhead hinge type PN7

Figure B. 11 - An example of an overhead hinge type PN7 for door blocks made of aluminum alloys 110

5 ´ 30

PN8-130

12,5

2,8 - 3,0

5 ´ 30

b 1

h

s

Number of pins

PV1-80

2,0 - 2,5

PV1-100

2,5 - 2,8

Figure B.15 - An example of a mortise hinge type PV1

Version 1

Execution 2

* When installing hinges on automated lines, in agreement with the consumer, it is allowed to use pins 35 mm long for casements of window blocks for residential and 45 mm for public buildings.

** The length of the pins is specified when ordering.

Dimensions in mm

Figure B.16 - An example of a mortise hinge type PV2

* For window units with triple glazing; pins - 4 pcs; the length of the pins is specified when ordering.

Figure B.17 - An example of a mortise hinge type PV3

Dimensions in mm

Figure B.18 - An example of a mortise hinge PV4

Figure B.19 - An example of a mortise hinge, size PV4- 100

Figure B. 20 - An example of a screw-in hinge type PVv1

Figure B. 21 - An example of a screw-in hinge type PVv2

Figure B. 22 - An example of a screw-in hinge type PVv3

Figure B. 23 - An example of an overlay hinge made of an aluminum profile for window and door blocks made of aluminum alloys and PVC profiles with a maximum weight of 80 kg

Figure B. 24 - An example of an aluminum profile overlay hinge for window and door blocks made of aluminum alloys and PVC profiles

Figure B. 25 - An example of an overlay hinge made of an aluminum profile for door blocks made of aluminum alloys and PVC profiles

Upper axleless ball hinge

Loop axisless ball lower (2)

where R etc - limiting external concentrated load acting in the plane of the sash;

R G - horizontal (pulling out) force acting on the loop;

R in - vertical load (shear) acting on the hinge rod;

H- sash height;

AT- sash width;

a- the distance that determines the location of the loop in the block;

G- mass of the sash.

The design loads for a particular loop are calculated using the formulas:

R g r = π d st l bunk k n [ τ cm ]; (3)

R in p = 0.1 d st l n ap [σ cm ], (4)

where R g r

R in r

d st - diameter of the screw-in loop rod;

l n ap - depth of cutting (thread);

k n - coefficient of completeness of thread cutting;

[ τ cm ] - the limiting value of the stress that occurs in the wood when it is crushed (tensile strength) across the fibers;

[ σ cm ] - the limiting value of stress (tensile strength) that occurs in wood when it is crushed along the fibers.

The condition for selecting a loop is:P G R ³ P G ; P in R ³ P in .

When calculating, it is necessary to take into account not only the mass and overall dimensions of a particular sash (leaf), but also the characteristics of the materials of the window (door) block.

Keywords: hinges, overhead hinges, mortise hinges, screw-in hinges, window blocks, door blocks